CC2640R2F-Q1 Datasheet, PDF (11/40 Pages) Texas Instruments – SimpleLink Bluetooth low energy Wireless MCU for Automotive

www.ti.com
CC2640R2F-Q1
SWRS201 – JANUARY 2017
5.6 1-Mbps GFSK (Bluetooth^® low energy Technology) – RX
Measured on the TI CC2640Q1EM-7ID reference design with T_c = 25°C, V_DDS = 3.0 V, f_RF = 2440 MHz, unless otherwise
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Receiver sensitivity
Differential mode. Measured at the CC2640Q1EM-
7ID SMA connector, BER = 10^–3
–96
dBm
Receiver saturation
Differential mode. Measured at the CC2640Q1EM-
7ID SMA connector, BER = 10^–3
4
dBm
Frequency error tolerance
Difference between the incoming carrier frequency
and the internally generated carrier frequency
–350
350 kHz
Data rate error tolerance
Difference between incoming data rate and the
internally generated data rate
–750
750 ppm
Co-channel rejection⁽¹⁾
Wanted signal at –67 dBm, modulated interferer in
channel,
BER = 10^–3
–6
dB
Selectivity, ±1 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±1 MHz,
BER = 10^–3
7 / 3 ⁽²⁾
dB
Selectivity, ±2 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±2 MHz,
BER = 10^–3
34 / 25⁽²⁾
dB
Selectivity, ±3 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±3 MHz,
BER = 10^–3
38 / 26⁽²⁾
dB
Selectivity, ±4 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
±4 MHz,
BER = 10^–3
42 / 29⁽²⁾
dB
Selectivity, ±5 MHz or more⁽¹⁾
Wanted signal at –67 dBm, modulated interferer at
≥ ±5 MHz, BER = 10^–3
32
dB
Wanted signal at –67 dBm, modulated interferer at
Selectivity, Image frequency⁽¹⁾ image frequency,
BER = 10^–3
25
dB
Selectivity, Image frequency
±1 MHz⁽¹⁾
Out-of-band blocking ⁽³⁾
Wanted signal at –67 dBm, modulated interferer at
±1 MHz from image frequency, BER = 10^–3
30 MHz to 2000 MHz
3 / 26⁽²⁾
–20
dB
dBm
Out-of-band blocking
2003 MHz to 2399 MHz
–5
dBm
Out-of-band blocking
2484 MHz to 2997 MHz
–8
dBm
Out-of-band blocking
3000 MHz to 12.75 GHz
–8
dBm
Intermodulation
Wanted signal at 2402 MHz, –64 dBm. Two
interferers at 2405 and 2408 MHz respectively, at
the given power level
–34
dBm
Spurious emissions,
30 to 1000 MHz
Conducted measurement in a 50-Ω single-ended
load. Suitable for systems targeting compliance with
EN 300 328, EN 300 440 class 2, FCC CFR47, Part
15 and ARIB STD-T-66
–71
dBm
Spurious emissions,
1 to 12.75 GHz
Conducted measurement in a 50 Ω single-ended
load. Suitable for systems targeting compliance with
EN 300 328, EN 300 440 class 2, FCC CFR47, Part
15 and ARIB STD-T-66
–62
dBm
RSSI dynamic range
70
dB
RSSI accuracy
±4
dB
(1) Numbers given as I/C dB.
(2) X / Y, where X is +N MHz and Y is –N MHz.
(3) Excluding one exception at F_wanted / 2, per Bluetooth Specification.
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: CC2640R2F-Q1
Specifications
11