TMS320DM6467T Datasheet, PDF (105/352 Pages) Texas Instruments – TMS320DM6467T Digital Media System-on-Chip

www.ti.com
TMS320DM6467T
SPRS605C – JULY 2009 – REVISED JUNE 2012
31
RSV
R-0
30
28
TSIF1P
R/W-001
27
RSV
R-0
26
24
TSIF0P
R/W-001
23
RSV
R-0
22
20
VP1P
R/W-001
15
14
12
11
10
8
RSV
EDMATC3P
RSV
EDMATC2P
R-0
R/W-010
R-0
R/W-010
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
7
RSV
R-0
6
4
EDMATC1P
R/W-010
Figure 4-13. MSTPRI2 Register
19
RSV
R-0
3
RSV
R-0
18
16
VP0P
R/W-001
2
0
EDMATC0P
R/W-010
BIT
31
30:28
27
26:24
23
22:20
19
18:16
15
14:12
11
10:8
7
6:4
3
2:0
NAME
RSV
TSIF1P
RSV
TSIF0P
RSV
VP1P
RSV
VP0P
RSV
EDMATC3P
RSV
EDMATC2P
RSV
EDMATC1P
RSV
EDMATC0P
Table 4-17. MSTPRI2 Register Bit Descriptions
DESCRIPTION
Reserved. Read returns "0".
TSIF1 master port priority in System Infrastructure.
000 = Priority 0 (Highest)
100 = Priority 4
001 = Priority 1 [Default]
101 = Priority 5
010 = Priority 2
110 = Priority 6
011 = Priority 3
111 = Priority 7 (Lowest)
Reserved. Read returns "0".
TSIF0 master port priority in System Infrastructure.
000 = Priority 0 (Highest)
100 = Priority 4
001 = Priority 1 [Default]
101 = Priority 5
010 = Priority 2
110 = Priority 6
011 = Priority 3
111 = Priority 7 (Lowest)
Reserved. Read returns "0".
VPIF display master port priority in System Infrastructure. Same priority 0–7 selection as above.
"001" = Priority 1 [default].
Reserved. Read returns "0".
VPIF capture master port priority in System Infrastructure. Same priority 0–7 selection as above.
"001" = Priority 1 [default].
Reserved. Read returns "0".
EDMATC3 master port priority in System Infrastructure. Same priority 0–7 selection as above.
"010" = Priority 2 [default].
Reserved. Read returns "0".
EDMATC2 master port priority in System Infrastructure. Same priority 0–7 selection as above.
"010" = Priority 2 [default].
Reserved. Read returns "0".
EDMATC1 master port priority in System Infrastructure. Same priority 0–7 selection as above.
"010" = Priority 2 [default].
Reserved. Read returns "0".
EDMATC0 master port priority in System Infrastructure. Same priority 0–7 selection as above.
"010" = Priority 2 [default].
4.6.2 Peripheral Selection After Device Reset
After device reset, most peripheral configurations are done within the peripheral’s registers. This
section discusses some additional peripheral controls in the System Module. For information on
multiplexed pin controls that determine what peripheral pins are brought out to the pins, see
Section 4.7, Multiplexed Pin Configurations.
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TMS320DM6467T
Device Configurations 105