TIBPAL16L8-5C Datasheet, PDF (9/30 Pages) Texas Instruments – HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS

TIBPAL16L8-5C
HIGH-PERFORMANCE IMPACT-X ™ PAL^® CIRCUITS
SRPS011D – D3359, OCTOBER 1989 – REVISED SEPTEMBER 1992
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, V_CC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Voltage applied to disabled output (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating free-air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 75°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
NOTE 1: These ratings apply except for programming pins during a programming cycle or during a preload cycle.
recommended operating conditions
MIN NOM MAX UNIT
VCC
VIH
Supply voltage
High-level input voltage (see Note 2)
4.75
5 5.25 V
2
5.5 V
VIL
Low-level input voltage (see Note 2)
IOH
High-level output current
IOL
Low-level output current
TA
Operating free-air temperature
0.8 V
– 3.2 mA
24 mA
0
25
75 °C
NOTE 2: These are absolute voltage levels with respect to the ground pin of the device and include all overshoots due to system and/or tester
noise. Testing these parameters should not be attempted without suitable equipment.
electrical characteristics over recommended operating free-air temperature range
PARAMETER
TEST CONDITIONS
MIN TYP^† MAX UNIT
VIK
VCC = 4.75 V,
II = – 18 mA
–0.8 – 1.5 V
VOH
VCC = 4.75 V,
IOH = – 3.2 mA
2.4 2.7
V
VOL
IOZH‡
IOZL‡
VCC = 4.75 V,
VCC = 5.25 V,
VCC = 5.25 V,
IOL = 24 mA
VO = 2.7 V
VO = 0.4 V
0.3 0.5 V
100 µA
–100 µA
II
IIH‡
IIL‡
IOS§
VCC = 5.25 V,
VCC = 5.25 V,
VCC = 5.25 V,
VCC = 5.25 V,
VI = 5.5 V
VI = 2.7 V
VI = 0.4 V
VO = 0.5 V
100 µA
25 µA
–250 µA
– 30 –70 –130 mA
ICC
VCC = 5.25 V,
VI = 0,
Outputs open
180 mA
Ci
f = 1 MHz,
VI = 2 V
8.5
pF
Co
f = 1 MHz,
VO = 2 V
10
pF
† _{All typical values are at VCC = 5 V, TA = 25°C.}
‡ _{I/O leakage is the worst case of IOZL and IIL or IOZH and IIH, respectively.}
§ _{Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second. VO is set at 0.5 V to}
avoid test problems caused by test equipment ground degradation.
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
tpd
ten
tdis
FROM
(INPUT)
I, I/O
I, I/O
I, I/O
I, I/O
TO
(OUTPUT)
O, I/O
O, I/O
with up to 4 outputs
switching
with more than 4
outputs switching
O, I/O
O, I/O
TEST
CONDITIONS
R1 = 200 Ω,
R2 = 200 Ω,
See Figure 8
TIBPAL16L8-5CFN
MIN
MAX
TIBPAL16L8-5CJ
TIBPAL16L8-5CN
MIN
MAX
UNIT
1.5
5 1.5
5
ns
1.5
5 1.5
5.5
2
7
2
7 ns
2
7
2
7 ns
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily
include testing of all parameters.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
9