THS7360_1 Datasheet, PDF (28/43 Pages) Texas Instruments – 6-Channel Video Amplifier with 3-SD and 3-SD/ED/HD/Full-HD Fiters and High Gain

THS7360
SLOS674 – JUNE 2010
CVBS
S-Video Y’
S-Video C’
Y'/G'
P'_B/B'
P'_R/R'
THS7360
1 SD1 IN
SD1 OUT 20
R
2 SD2 IN
SD2 OUT 19
3 SD3 IN
SD3 OUT 18
4 NC
R
+2.7 V to
+5 V
5 V_S+
6 NC
Disable SD 17
GND 16
Disable HD 15
Disable SD
Disable SF
7 SF1 IN
SF1 OUT 14
R
8 SF2 IN
SF2 OUT 13
9 SF3 IN
SF3 OUT 12
10 Bypass SD Bypass SF 11
R
Bypass
SD LPF
R
Bypass
SF LPF
R
CVBS 1 Out
75 W
S-Video Y' 1 Out
75 W
S-Video C' 1 Out
75 W
Y'/G' 1 Out
75 W
P’_B/B' 1 Out
75 W
P'_R/R' 1 Out
75 W
www.ti.com
CVBS 1 Out
75 W
75 W
75 W
S-Video Y' 1 Out
75 W
75 W
75 W S-Video C' 1 Out
75 W
75 W
75 W
Y'/G' 1 Out
75 W
75 W
75 W
P'_B/B' 1 Out
75 W
75 W
75 W
P’_R/R' 1 Out
75 W
75 W
75 W
(1) SF indicates selectable filter.
Figure 47. Typical Six-Channel System with DC-Coupled Line Driving and Two Outputs Per Channel
One concern of dc-coupling arises, however, if the
line is terminated to ground. If the ac-bias input
configuration is used, the output of the THS7360 has
a dc bias on the output, such as 1.6 V. With two lines
terminated to ground, this configuration allows a dc
current path to flow, such as 1.6 V/75 Ω = 21.3 mA.
The result of this configuration is a slightly decreased
high-output voltage swing and an increase in power
dissipation of the THS7360. While the THS7360 was
designed to operate with a junction temperature of up
to +125°C, care must be taken to ensure that the
junction temperature does not exceed this level or
else long-term reliability could suffer. Using a 5-V
supply, this configuration can result in an additional
dc power dissipation of (5 V – 1.6 V) × 21.3 mA =
72.5 mW per channel. With a 3.3-V supply, this
dissipation reduces to 36.2 mW per channel. The
overall low quiescent current of the THS7360 design
minimizes potential thermal issues even when using
the TSSOP package at high ambient temperatures,
but power and thermal analysis should always be
examined in any system to ensure that no issues
arise. Be sure to use RMS power and not
instantaneous power when evaluating the thermal
performance.
Note that the THS7360 can drive the line with
dc-coupling regardless of the input mode of
operation. The only requirement is to make sure the
video line has proper termination in series with the
output (typically 75 Ω). This requirement helps isolate
capacitive loading effects from the THS7360 output.
Failure to isolate capacitive loads may result in
instabilities with the output buffer, potentially causing
ringing or oscillations to appear. The stray
capacitance that appears directly at the THS7360
output pins should be kept below 20 pF for the fixed
SD filter channels and below 15 pF for the selectable
28
Submit Documentation Feedback
Product Folder Link(s): THS7360
Copyright © 2010, Texas Instruments Incorporated