CC2630_15 Datasheet, PDF (12/50 Pages) Texas Instruments – CC2630 SimpleLink 6LoWPAN / ZigBee Wireless MCU

CC2630
SWRS177 – FEBRUARY 2015
www.ti.com
5 Specifications
5.1 Absolute Maximum Ratings⁽¹⁾⁽²⁾
[over operating free-air temperature range (unless otherwise noted)] Under no circumstances must the absolute maximum
ratings be violated. Stress exceeding one or more of the limiting values may cause permanent damage to the device.
MIN
MAX UNIT
Supply voltage, VDDS⁽³⁾
VDDR supplied by internal DC/DC regulator or
internal GLDO
–0.3
4.1
V
Supply voltage, VDDS⁽³⁾ and VDDR
External regulator mode (VDDS and VDDR pins
connected on PCB)
–0.3
2.25
V
Voltage on any digital pin⁽⁴⁾
–0.3
VDDS+0.3, max
4.1
V
Voltage on crystal oscillator pins,
X32K_Q1, X32K_Q2, X24M_N and
X24M_P
–0.3
VDDR+0.3, max
2.25
V
Internal fixed or relative reference, voltage
scaling enabled
–0.3
VDDS
Internal fixed reference, voltage scaling disabled
–0.3
1.49
Voltage on ADC input (V_in)
Internal relative reference, voltage scaling
disabled
–0.3
VDDS / 2.9
V
External reference, voltage scaling enabled
–0.3
min (V_ref × 2.9,
VDDS)
Voltage on external ADC reference
(V_ref)
Input RF level
External reference, voltage scaling disabled
–0.3
–0.3
V_ref
1.6
V
+5 dBm
T_stg
Storage temperature
–40
150
°C
(1) All voltage values are with respect to VDDS, unless otherwise noted.
(2) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(3) VDDS2 and VDDS3 needs to be at the same potential as VDDS.
(4) Including analog capable DIO.
5.2 ESD Ratings
V_ESD
Electrostatic discharge
(ESD) performance:
Human Body Model (HBM), per ANSI/ESDA/JEDEC
JS001 ⁽¹⁾
Charged Device Model (CDM), per JESD22-C101⁽²⁾
All pins
RF pins
non-RF pins
VALUE
±2500
±750
±750
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
UNIT
V
5.3 Recommended Operating Conditions
The operating conditions for CC2630 are listed below.
Ambient temperature range
Operating supply voltage
(VDDS and VDDR), external
regulator mode
Operating supply voltage
(VDDS)
Rising supply voltage slew rate
Falling supply voltage slew rate
For operation in 1.8 V systems
(VDDS and VDDR pins connected on PCB, internal DC/DC
cannot be used)
For operation in battery-powered and 3.3 V systems
(internal DC/DC can be used to minimize power consumption)
MIN
MAX UNIT
–40
85 °C
1.7
1.95 V
1.8
3.8 V
0
100 mV/us
0
20 mV/us
12
Specifications
Submit Documentation Feedback
Product Folder Links: CC2630
Copyright © 2015, Texas Instruments Incorporated