80C154 Datasheet, PDF (16/24 Pages) TEMIC Semiconductors – CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller

80C154/83C154
Absolute Maximum Ratings*
Ambient Temperature Under Bias :
M = Military . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . –65°C to + 150°C
Voltage on VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to + 7 V
Voltage on Any Pin to VSS . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W
** This value is based on the maximum allowable die temperature and
the thermal resistance of the package
* Notice
Stresses at or above those listed under “ Absolute Maximum Ratings”
may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions may affect
device reliability.
DC Parameters
TA = –55°C + 125°C ; Vss = 0 V ; Vcc = 5 V ± 10 % ; F = 0 to 36 MHz
SYMBOL
PARAMETER
VIL Input Low Voltage
VIH Input High Voltage (Except XTAL and RST)
VIH1 Input High Voltage (for XTAL and RST)
VOL Output Low Voltage (Port 1, 2 and 3)
VOL1 Output Low Voltage (Port 0, ALE, PSEN)
VOH Output High Voltage (Port 1, 2, 3)
VOH1 Output High Voltage
(Port 0 in External Bus Mode, ALE, PEN)
IIL
ILI
ITL
IPD
RRST
Logical 0 Input Current (Ports 1, 2 and 3)
Input leakage Current
Logical 1 to 0 Transition Current
(Ports 1, 2 and 3)
Power Down Current
RST Pulldown Resistor
CIO Capacitance of I/O Buffer
ICC Power Supply Current
Freq = 1 MHz Icc op
Icc idle
Freq = 6 MHz Icc op
Icc idle
Freq ≥ 12 MHz Icc op = 1.3 Freq (MHz) + 4.5 mA
Icc idle = 0.36 Freq (MHz) + 2.7 mA
MIN
MAX UNIT TEST CONDITIONS
– 0.5
0.2 Vcc – 0.1 V
0.2 Vcc + 1.4 Vcc + 0.5
V
0.7 Vcc
Vcc + 0.5
V
0.45
V IOL = 1.6 mA (note 2)
0.45
V IOL = 3.2 mA (note 2)
2.4
V IOH = – 60 µA
Vcc = 5 V ± 10 %
0.75 Vcc
V IOH = – 25 µA
0.9 Vcc
V IOH = – 10 µA
2.4
V IOH = – 400 µA
Vcc = 5 V ± 10 %
0.75 Vcc
V IOH = – 150 µA
0.9 Vcc
V IOH = – 40 µA
– 75
µA Vin = 0.45 V
±10
µA 0.45 < Vin < Vcc
– 750
µA Vin = 2.0 V
75
µA Vcc = 2.0 V to 5.5 V (note 1)
50
200
KOh
m
10
pF fc = 1 MHz, Ta = 25_C
Vcc = 5.5 V
1.8
mA
1
mA
10
mA
4
mA
16
MATRA MHS
Rev.F (14 Jan. 97)