80C154 Datasheet, PDF (14/24 Pages) TEMIC Semiconductors – CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller

80C154/83C154
Electrical Characteristics
Absolute Maximum Ratings*
Ambiant Temperature Under Bias :
C = commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
I = industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . –65°C to + 150°C
Voltage on VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to + 7 V
Voltage on Any Pin to VSS . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W**
** This value is based on the maximum allowable die temperature and
the thermal resistance of the package
* Notice
Stresses at or above those listed under “ Absolute Maximum Ratings”
may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions may affect
device reliability.
DC Parameters
TA = 0°C to 70°C ; Vcc = 0 V ; Vcc = 5 V ± 10 % ; F = 0 to 36 MHz
TA = –40°C + 85°C ; Vcc = 0 V ; Vcc = 5 V ± 10 % ; F = 0 to 36 MHz
SYMBOL
PARAMETER
VIL Input Low Voltage
VIH Input High Voltage (Except XTAL and RST)
MIN
– 0.5
0.2 Vcc + 1.4
MAX UNIT
0.2 Vcc – 0.1 V
Vcc + 0.5
V
TEST CONDITIONS
VIH1
VOL
Input High Voltage (for XTAL and RST)
Output Low Voltage (Port 1, 2 and 3)
VOL1 Output Low Voltage (Port 0, ALE, PSEN)
VOH Output High Voltage Port 1, 2 and 3
0.7 Vcc
Vcc – 0.3
Vcc – 0.7
Vcc – 1.5
Vcc + 0.5
0.3
0.45
1.0
0.3
0.45
1.0
V
V IOL = 100 µA
V IOL = 1.6 mA (note 2)
V IOL = 3.5 mA
V IOL = 200 µA
V IOL = 3.2 mA (note 2)
V IOL = 7.0 mA
V IOH = – 10 µA
V IOH = – 30 µA
V IOH = – 60 µA
VCC = 5 V ± 10 %
VOH1 Output High Voltage (Port 0, ALE, PSEN)
Vcc – 0.3
V IOH = – 200 µA
Vcc – 0.7
V IOH = – 3.2 mA
IIL Logical 0 Input Current (Ports 1, 2 and 3)
ILI Input leakage Current
ITL Logical 1 to 0 Transition Current
(Ports 1, 2 and 3)
IPD Power Down Current
Vcc – 1.5
– 50
+/– 10
– 650
50
V IOH = – 7.0 mA
VCC = 5 V ± 10 %
µA Vin = 0.45 V
µA 0.45 < Vin < Vcc
µA Vin = 2.0 V
µA Vcc = 2.0 V to 5.5 V (note 1)
RRST
CIO
RST Pulldown Resistor
Capacitance of I/O Buffer
50
200
KOhm
10
pF fc = 1 MHz, Ta = 25_C
ICC Power Supply Current
Freq = 1 MHz Icc op
Icc idle
Freq = 6 MHz Icc op
Icc idle
Freq ≥ 12 MHz Icc op = 1.3 Freq (MHz) + 4.5 mA
Icc idle = 0.36 Freq (MHz) + 2.7 mA
Vcc = 5.5 V
1.8
mA
1
mA
10
mA
4
mA
14
MATRA MHS
Rev.F (14 Jan. 97)