K0900E70 Datasheet, PDF (75/224 Pages) Teccor Electronics – Thyristor Product Catalog

Data Sheets
SCRs
130
120
110
16
A
TO-220
(Non-isolated)
and
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measured
as shown on dimensional drawings
TO-263
100
20 A TO-220
90
(Isolated)
80
10 A TO-220
70
(Non-isolated)
60
50
0
15 A TO-220
(Isolated)
2
4
6
8
10
12
14
Average On-state Current [I_T(AV)] – Amps
Figure E6.13 Maximum Allowable Case Temperature versus
Average On-state Current (10 A through 20 A)
130
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
120
CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure as
shown on dimensional drawings
110
35 A TO-218 (Non-isolated)
35 A TO-218 (Isolated)
100
90
25A TO-220 (Isolated)
80
70
25A TO-220 (Non-isolated)
and TO-263
60
50
0
.4
8
12
16
20
24
Average On-state Current [I_T(AV)] – Amps
Figure E6.14 Maximum Allowable Case Temperature versus
Average On-state Current (25 A and 35 A)
130
120
110
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure as
shown on dimensional drawings
100
90
40 A TO-220
(Non-isolated)
and TO-263
80
55 A TO-218X
70
(Non-isolated)
65 A TO-218X
60
(Isolated)
70 A TO-218X
(Non-isolated)
50
0
10
20
30
40
50
Average On-state Current [I_T(AV)] – Amps
Figure E6.15 Maximum Allowable Case Temperature versus
Average On-state Current (40 A through 70 A)
130
120
110
100 _{55 A TO-220}
(Non-isolated)
90 ^{and TO-263 *}
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure
as shown on dimensional drawings
55 A TO-218AC (Non-isolated) *
65 A TO-218AC
(Isolated) *
80 _{* The R, K, or M package}
rating is intended only for high
surge condition use and is not
70 recommended for >32 A (AV)
continuous current use since narrow
pin lead temperature can exceed PCB
60 solder melting temperature. J or W
packages are recommended for >32 A
(AV) continuous current requirements.
50
0
10
20
30
40
50
Average On-state Current [I_T(AV)] – Amps
Figure E6.16 Maximum Allowable Case Temperature versus
Average On-state Current (55 A and 65 A)
2.0
INITIAL ON-STATE CURRENT =
200 mA dc for 1 A to 20 A Devices
and 400 mA dc for 25 A to 70 A Devices
1.5
1.0
.5
0
-40 -15
+25
+65
+105 +125
Case Temperature (T_C) – ˚C
Figure E6.17 Normalized dc Holding Current versus Case Temperature
2.0
1.5
1.0
0.5
0
-40
-15
+25
+65
+105 +125
Case Temperature (T_C) – ˚C
Figure E6.18 Normalized DC Gate-Trigger Current versus
Case Temperature
©2002 Teccor Electronics
Thyristor Product Catalog
E6 - 9
http://www.teccor.com
[phone]