K0900E70 Datasheet, PDF (69/224 Pages) Teccor Electronics – Thyristor Product Catalog

Data Sheets
SCRs
I_DRM & I_RRM
(14)
V_TM
(3)
V_GT
I_H
I_GM
(8) (5) (13) (12)
(17)
P_GM
(12)
P_G(AV) I_TSM
(6) (10)
dv/dt
I²t
di/dt
t_gt
t_q
(7) (9) (10)
mAmps
TC = TC = TC =
25 °C 100 °C 125 °C
MAX
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.02
3
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.02
3
0.01 0.2 0.5
0.01 0.2 0.5
0.01 0.2 0.5
0.02 0.5
1
0.02
3
0.01 0.5
1
0.01 0.5
1
0.01 0.5
1
0.02 0.5
1
0.02
3
Volts
TC =
25 °C
MAX
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
Volts
TC =
25 °C
MAX
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
mAmps
MAX
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
40
40
40
40
40
Amps
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Watts
15
15
15
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
Watts
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Amps
60/50 Hz
30/25
30/25
30/25
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
100/83
120/100
120/100
120/100
120/100
120/100
Volts/µSec
TC = TC =
100 °C 125 °C
MIN MIN
40
20
40
20
40
20
350
250
350
250
300
225
250
200
100
350
250
350
250
300
225
250
200
100
350
250
350
250
300
225
250
200
100
350
250
350
250
300
225
250
200
100
Amps²Sec
3.7
3.7
3.7
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
60
60
60
60
60
Amps/µSec
50
50
50
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
µSec
TYP
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
µSec
MAX
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
Electrical Specification Notes
(1) See Figure E6.5 through Figure E6.16 for current rating at
specified operating case temperature.
(2) See Figure E6.1 and Figure E6.2 for free air current rating.
(3) See Figure E6.19 and Figure E6.20 for instantaneous on-state
current versus on-state voltage (typical).
(4) See Figure E6.18 for I_GT versus T_C.
(5) See Figure E6.17 for I_H versus T_C.
(6) For more than one full cycle rating, see Figure E6.23.
(7) See Figure E6.22 for tgt versus IGT.
(8) See Figure E6.21 for VGT versus TC.
(9) Test conditions are as follows:
• IT = 1 A for 1 A devices and 2 A for all other devices
• Pulse duration = 50 µs, dv/dt = 20 V/µs, di/dt = -10 A/µs for 1 A
devices, and -30 A/µs for other devices
• I_GT = 200 mA at turn-on
(10) See Figure E6.5 through Figure E6.10 for maximum allowable
case temperatures at maximum rated current.
(11) See package outlines for lead form configuration. When ordering
special lead forming, add type number as suffix to part number.
(12) Pulse width ≤10 µs
(13) Initial on-state current = 200 mA dc for 1 A through 16 A devices;
400 mA dc for 20 A through 70 A devices.
(14) TC = TJ for test conditions in off state.
(15) The R, K, or M package rating is intended for high surge condition
use only and not recommended for ≥50 A rms continuous current
use since narrow pin lead temperature can exceed PCB solder melting
temperature. Teccor's J package or W package is recommended
for ≥50 A rms continuous current requirements.
(16) For various durations of an exponentially decaying current
waveform, see Figure E6.3 and Figure E6.4. (t_W is defined as
5 time constants.)
(17) Minimum non-trigger V_GT at 125 °C is 0.2 V.
©2002 Teccor Electronics
Thyristor Product Catalog
E6 - 3
http://www.teccor.com
[phone]