STM32F469XX Datasheet, PDF (68/217 Pages) STMicroelectronics – ARMCortex-M4 32b MCU+FPU, 225DMIPS, up to 2MB Flash/384+4KB RAM, USB OTG HS/FS, Ethernet, FMC, dual Quad-SPI, Graphical accelerator, Camera IF, LCD-TFT & MIPI DSI

Pinouts and pin description
STM32F469xx
Table 10. STM32F469xx pin and ball definitions (continued)
Pin number
Pin name
(function after
reset)⁽¹⁾
Alternate functions
Additional
functions
TIM4_CH2, I2C1_SDA,
96 136 B4 A9 B5 165 196 B5
PB7
I/O FT - USART1_RX, FMC_NL,
-
DCMI_VSYNC, EVENTOUT
97 137 A5 F8 D6 166 197 E6
BOOT0
I B-
-
VPP
TIM4_CH3, TIM10_CH1,
I2C1_SCL, CAN1_RX,
98 138 D4 B9 A5 167 198 A7
PB8
I/O FT - ETH_MII_TXD3, SDIO_D4,
-
DCMI_D6, LCD_B6,
EVENTOUT
TIM4_CH4, TIM11_CH1,
I2C1_SDA,
99 139 C4 E9 B4 168 199 B4
PB9
I/O FT -
SPI2_NSS/I2S2_WS,
CAN1_TX, SDIO_D5,
-
DCMI_D7, LCD_B7,
EVENTOUT
NC
(2)
140
A4
A10
A4
169 200
A6
PE0
I/O FT -
TIM4_ETR, UART8_Rx,
FMC_NBL0, DCMI_D2,
-
EVENTOUT
NC
(2)
141
A3
C9
A3 170 201 A5
PE1
I/O FT -
UART8_Tx, FMC_NBL1,
DCMI_D3, EVENTOUT
-
- - E3 B10 D5 - 202 F6
VSS
S --
-
-
- 142 C3 D9 C6 171 203 E5
PDR_ON
S --
-
-
100 143 D3 A11 C5 172 204 E7
VDD
S --
-
-
TIM8_BKIN, FMC_NBL2,
- - B3 D10 D4 173 205 C3
PI4
I/O FT -
DCMI_D5, LCD_B4,
-
EVENTOUT
TIM8_CH1, FMC_NBL3,
- - A2 C10 C4 174 206 D3
PI5
I/O FT - DCMI_VSYNC, LCD_B5,
-
EVENTOUT
TIM8_CH2, FMC_D28,
- - A1 B11 C3 175 207 D6
PI6
I/O FT -
DCMI_D6, LCD_B6,
-
EVENTOUT
TIM8_CH3, FMC_D29,
- - B1 A12 C2 176 208 D4
PI7
I/O FT -
DCMI_D7, LCD_B7,
-
EVENTOUT
1. Function availability depends on the chosen device.
2. NC (not-connected) pins are not bonded. They must be configured by software to output push-pull and forced to “0” in the
output data register to avoid extra current consumption in low power modes.
3. PC13, PC14, PC15 and PI8 are supplied through the power switch. Since the switch only sinks a limited amount of current
(3 mA), the use of GPIOs PC13 to PC15 and PI8 in output mode is limited:
- The speed should not exceed 2 MHz with a maximum load of 30 pF.
- These I/Os must not be used as a current source (e.g. to drive an LED).
4. Main function after the first backup domain power-up. Later on, it depends on the contents of the RTC registers even after
reset (because these registers are not reset by the main reset). For details on how to manage these I/Os, refer to the RTC
register description sections in the STM32F4xx reference manual, available from the STMicroelectronics website:
www.st.com.
5. FT = 5 V tolerant except when in analog mode or oscillator mode (for PC14, PC15, PH0 and PH1).
68/217
DocID028196 Rev 3