EMC2300_11 Datasheet, PDF (59/82 Pages) SMSC Corporation – Fan Control Device with High Frequency PWM and Temperature Monitors

Fan Control Device with High Frequency PWM and Temperature Monitors
Datasheet
8.2.12 Registers 54-5Bh: Fan Tachometer Low Limit
Register
Address
54h
55h
56h
57h
58h
59h
5Ah
5Bh
Read/
Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 8.21 Registers 54-5Bh: Fan Tachometer Low Limit
Register Name
Tach1 Minimum LSB
Tach1 Minimum MSB
Tach2 Minimum LSB
Tach2 Minimum MSB
Tach3 Minimum LSB
Tach3 Minimum MSB
Tach4 Minimum LSB
Tach4 Minimum MSB
Bit 7
(MSb)
7
15
7
15
7
15
7
15
Bit 6
6
14
6
14
6
14
6
14
Bit 5
5
13
5
13
5
13
5
13
Bit 4 Bit 3 Bit 2 Bit 1
4
3
2
1
12
11
10
9
4
3
2
1
12
11
10
9
4
3
2
1
12
11
10
9
4
3
2
1
12
11
10
9
Bit 0
(LSb)
0
8
0
8
0
8
0
8
Default
Value
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
8.2.13
Setting the Lock bit has no effect on these registers.
The Fan Tachometer Low Limit registers indicate the tachometer reading that, if exceeded, the
corresponding bit will be set in the Interrupt Status Register 2 register. This register represents a
number of clock counts between the programmed number of tach edges and therefore as the number
increases, the effective RPM that it represents will decrease. The limit represents a fixed fan speed
(though the TACH measurement options may limit fan speeds that can be measured). See
Section 8.2.3 for a description of the TACH data formatting.
In Auto Fan Control mode, the fan can run at high speeds (100% duty cycle), so care should be taken
in software to ensure that the limit is low enough not to cause sporadic alerts. Note that an interrupt
status event will be generated when the tachometer reading is greater than the minimum tachometer
limit.
The fan tachometer will not cause a bit to be set in the interrupt status register if the current value in
the associated Current PWM Duty registers is 00h or if the PWM is disabled via the PWM
Configuration Register.
Interrupts will never be generated for a fan if its tachometer minimum is set to FFFFh.
Registers 5C-5Eh: PWM Configuration
Register
Address
5Ch
5Dh
5Eh
Read/
Write
R/W
R/W
R/W
Table 8.22 Registers 5C-5Eh: PWM Configuration
Register Name
PWM 1 Configuration
PWM 2 Configuration
PWM 3 Configuration
Bit 7
(MSb)
ZON2
ZON2
ZON2
Bit 6
ZON1
ZON1
ZON1
Bit 5
ZON0
ZON0
ZON0
Bit 4
INV
INV
INV
Bit 3
RES
RES
RES
Bit 2
SPIN2
SPIN2
SPIN2
Bit 1
SPIN1
SPIN1
SPIN1
Bit 0
(LSb)
SPIN0
SPIN0
SPIN0
Default
Value
62h
62h
62h
These registers become read only when the Lock bit is set. Any further attempts to write to these
registers shall have no effect.
Bits [7:5] Zone/Mode
Bits [7:5] of the PWM Configuration registers associate each PWM with a temperature sensor.
SMSC EMC2300
59
DATASHEET
Revision 0.32 (06-23-08)