LAN8710 Datasheet, PDF (15/79 Pages) SMSC Corporation – MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and flexPWR Technology in a Small Footprint

MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and flexPWR^® Technology in a Small Footprint
Datasheet
Table 3.2 MII/RMII Signals (continued) 32-QFN (continued)
SIGNAL
NAME
TXD2
TXD3
nINT/
TXER/
TXD4
TXEN
TXCLK
RXD0/
MODE0
RXD1/
MODE1
RXD2/
RMIISEL
RXD3/
PHYAD2
32-QFN
PIN # TYPE
DESCRIPTION
24
I8 Transmit Data 2: The MAC transmits data to the transceiver using this
signal in MII Mode.
„ This signal should be grounded in RMII Mode.
25
I8 Transmit Data 3: The MAC transmits data to the transceiver using this
signal in MII Mode.
„ This signal should be grounded in RMII Mode.
18
IOPU nINT – Active low interrupt output. Place an external resistor pull-up to
VDDIO.
„ See Section 4.10 for information on how nINTSEL is used to determine
the function for this pin.
TXER – MII Transmit Error: When driven high, the 4B/5B encode process
substitutes the Transmit Error code-group (/H/) for the encoded data word.
This input is ignored in 10Base-T operation.
TXD4 – MII Transmit Data 4: In Symbol Interface (5B Decoding) mode, this
signal becomes the MII Transmit Data 4 line, the MSB of the 5-bit symbol
code-group.
„ TXD4 is not used in RMII Mode.
„ This signal is mux’d with nINT
21
IPD Transmit Enable: Indicates that valid data is presented on the TXD[3:0]
signals, for transmission. In RMII Mode, only TXD[1:0] have valid data.
20
O8 Transmit Clock: Used to latch data from the MAC into the transceiver.
„ MII (100BT): 25MHz
„ MII (10BT): 2.5MHz
„ This signal is not used in RMII Mode.
11
IOPU RXD0 – Receive Data 0: Bit 0 of the 4 data bits that are sent by the
transceiver in the receive path.
MODE0 – PHY Operating Mode Bit 0: set the default MODE of the PHY.
„ See Section 5.3.9.2 for information on the MODE options.
10
IOPU RXD1 – Receive Data 1: Bit 1 of the 4 data bits that are sent by the PHY
in the receive path.
MODE1 – PHY Operating Mode Bit 1: set the default MODE of the PHY.
„ See Section 5.3.9.2 for information on the MODE options.
9
IOPD RXD2 – Receive Data 2: Bit 2 of the 4 data bits that are sent by the
transceiver in the receive path.
„ The RXD2 signal is not used in RMII Mode.
RMIISEL – MII/RMII Mode Selection: Latched on the rising edge of the
internal reset (nRESET) based on the following strapping:
„ By default, MII mode is selected.
„ Pull this pin high to VDDIO with an external resistor to select RMII mode,
8
IOPD RXD3 – Receive Data 3: Bit 3 of the 4 data bits that are sent by the
transceiver in the receive path.
„ This signal is not used in RMII Mode.
„ This signal is mux’d with PHYAD2
PHYAD2 – PHY Address Bit 2: set the SMI address of the transceiver.
„ See Section 5.3.9.1 for information on the ADDRESS options.
SMSC LAN8710/LAN8710i
15
DATASHEET
Revision 1.0 (04-15-09)