AAT2601B Datasheet, PDF (26/39 Pages) Skyworks Solutions Inc. – Total Power Solution for Portable Applications

DATA SHEET
AAT2601B
Total Power Solution for Portable Applications
Constant Current Mode Charge Current
vs. ISET Resistor
(V_IN = 5V; V_BAT = 3.6V)
1400
1200
1000
800
600
400
200
0
0.1
1
10
100
ISET Resistor (kΩ)
ISET Voltage vs. Battery Voltage
(CHGIN = 5.0V, R_ISET = 1.24kΩ)
1.4
1.2
1
0.8
0.6
0.4
0.2
0
2.5
2.9
3.3
3.7
4.1
4.5
Battery Voltage (V)
Figure 5: Constant Current Mode Charge I_{CH_CC} Setting vs. I_SET Resistor
and I_SET Voltage vs. Battery Voltage.
Reverse Battery Leakage
The AAT2601B includes internal circuitry that eliminates
the need for series blocking diodes, reducing solution
size and cost as well as dropout voltage relative to con-
ventional battery chargers. When the input supply is
removed or when CHGIN goes below the AAT2601B’s
under voltage-lockout (UVLO) voltage, or when CHGIN
drops below V_BAT, the AAT2601B automatically reconfig-
ures its power switches to minimize current drain from
the battery.
Adapter Power Indicator (ADPP)
This is an open drain output which will pull low when
V_CHGIN > 4.5V. When this happens, depending on the sta-
tus of the USE_USB pin, the charge current will be reset
to the default ISET values or I²C programmed values.
Charge Status Output (STAT)
The AAT2601B provides battery charging status via a
status pin. This pin is a buffered output with a supply
level up to the LDO1 output. The status pin can indicate
the following conditions:
Event Description
No battery charging activity
Battery charging
Charging completed
STAT
Low (to GND)
High (to V_OUT1)
Low (to GND)
Table 2: Charge Status Output (STAT).
CHGIN Bypass Capacitor Selection
CHGIN is the power input for the AAT2601B battery char-
ger. The battery charger is automatically enabled when-
ever a valid voltage is present on CHGIN. In most appli-
cations, CHGIN is connected to either a wall adapter or
USB port. Under normal operation, the input of the char-
ger will often be “hot-plugged” directly to a powered USB
or wall adapter cable, and supply voltage ringing and
overshoot may appear at the CHGIN pin. A high quality
capacitor connected from CHGIN to GND, placed as close
as possible to the IC, is sufficient to absorb the energy.
Wall-adapter powered applications provide flexibility in
input capacitor selection, but the USB specification pres-
ents limitations to input capacitance selection. In order
to meet both the USB 2.0 and USB OTG (On The Go)
specifications while avoiding USB supply under-voltage
conditions resulting from the current limit slew rate
(100mA/μs) limitations of the USB bus, the CHGIN
bypass capacitance value must be between 1μF and
4.7μF. Ceramic capacitors are often preferred for bypass-
ing due to their small size and good surge current rat-
ings, but care must be taken in applications that can
encounter hot plug conditions as their very low ESR, in
combination with the inductance of the cable, can create
a high-Q filter that induces excessive ringing at the
CHGIN pin. This ringing can couple to the output and be
mistaken as loop instability, or the ringing may be large
enough to damage the input itself. Although the CHGIN
pin is designed for maximum robustness and an absolute
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
26
202181B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 19, 2013