S112S01 Datasheet, PDF (2/5 Pages) Sharp Electrionic Components – SIP Type SSR for Medium Power Control

S112S01 Series/S116S01 Series
s Absolute Maximum Ratings
Input
Output
Parameter
Forward current
Reverse voltage
RMS ON-state
current
S112S01 Series
S116S01 Series
*1 _{Peak one cycle}
S112S01 Series
surge current
S116S01 Series
Repetitive peak
OFF-state voltage
Non-repetitive peak
OFF-state voltage
S112S01 / S112S02
S116S01 / S116S02
S212S01 / S212S02
S216S01 / S216S02
S112S01 / S112S02
S116S01 / S116S02
S212S01 / S212S02
S216S01 / S216S02
Critical rate of rise of ON-state current
Operating frequency
*2 _{Isolation voltage}
Operating temperature
Storage temperature
*3_{Soldering temperature}
Symbol
IF
VR
IT
I surge
VDRM
VDSM
dI/dt
f
Viso
Topr
Tstg
Tsol
(Ta = 25˚C )
Rating
50
6
*4₁₂
*5₁₆
120
160
400
600
400
600
50
45 to 65
4 000
- 25 to + 100
- 30 to + 125
260
Unit
mA
V
A rms
A rms
A
A
V
V
V
V
A/µ s
Hz
V rms
˚C
˚C
˚C
*1 AC 60Hz sine wave, Tj = 25˚C
start
*2 AC 60Hz for 1 minute, 40 to 60
% RH. Apply voltages between
input and output by the
dielectric withstand voltage
tester with zero-cross circuit.
( Input and output shall be short-
ed respectively) .
( Note )
When the isolation voltage is
necessary at using external
heat sink, please use the in-
sulation sheet.
*3 For 10 seconds
*4 TC<=70˚C
*5 TC<=60˚C
s Electrical Characteristics
Parameter
Input
Forward voltage
Reverse current
Repetitive peak OFF-state current
ON-state voltage
S112S01 Series
S116S01 Series
Holding current
Output
Critical rate of rise of OFF-state voltage
Transfer
charac-
teristics
Critical rate of rise of commutating
OFF-state voltage
Zero-cross voltage
Minimum trigger
current
S112S02 / S212S02
S116S02 / S216S02
S112S01 / S212S01
S116S01 / S216S01
S112S02 / S212S02
S116S02 / S216S02
Isolation resistance
Turn-on time
S112S01 / S212S01
S116S01 / S216S01
S112S02 / S212S02
S116S02 / S216S02
Turn-off time
Thermal resistance
(Between junction and case)
S112S01 series
S116S01 series
Thermal resistance ( Between junction and ambience )
Symbol
VF
IR
I DRM
VT
IH
dV/dt
( dV/dt )_C
V OX
I FT
R ISO
t on
t off
R th(j - c)
R th(j - a)
Conditions
IF = 20mA
VR = 3V
V D = V DRM
Resistance load
IF = 20mA, IT = 12Arms
Resistance load
IF = 20mA, IT = 16Arms
-
V D = 2/3 • V DRM
T j = 125˚C, VD = 400V, *6
IF = 8mA
VD = 12V, R L= 30 Ω
VD = 6V, R L= 30 Ω
DC500V, RH = 40 to 60 %
AC 50Hz
AC 50Hz
-
-
-
*6 S112S01 Series: dI T /dt = - 6A/ms
S116S01 Series: dI T /dt = - 8A/ms
MIN.
-
-
-
-
-
-
30
5
-
-
-
10¹⁰
-
-
-
-
-
-
TYP.
1.2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3.8
3.3
40
(Ta = 25˚C )
MAX.
1.4
10^{- 4}
10^{- 4}
1.5
1.5
50
-
Unit
V
A
A
V rms
V rms
mA
V/µ s
-
V/µ s
35
V
8
mA
8
mA
-
Ω
1
ms
10
ms
10
ms
-
˚C/W
-
˚C/W
-
˚C/W