DS_M368L3223DTL Datasheet, PDF (9/12 Pages) Samsung semiconductor – 256MB DDR SDRAM MODULE

M368L3223DTL
184pin Unbuffered DDR SDRAM MODULE
Parameter
Symbol
-TCB3
(DDR333)
Min
Max
-TCA2
(DDR266A)
Min
Max
-TCB0
(DDR266B)
Min
Max
Unit Note
Mode register set cycle time
tMRD
12
15
15
ns
DQ & DM setup time to DQS
tDS
0.45
0.5
0.5
ns 7,8,9
DQ & DM hold time to DQS
tDH
0.45
0.5
0.5
ns _7,8,9
Control & Address input pulse width
tIPW
2.2
2.2
2.2
ns
DQ & DM input pulse width
tDIPW
1.75
1.75
1.75
ns
Power down exit time
tPDEX
6
7.5
7.5
ns
Exit self refresh to non-Read command tXSNR
75
75
75
ns
4
Exit self refresh to read command
tXSRD
200
200
200
tCK
Refresh interval time
tREFI
7.8
7.8
7.8
us
1
Output DQS valid window
tQH
tHP
-
tHP
-
tHP
-
ns
5
-tQHS
-tQHS
-tQHS
Clock half period
tHP
tCLmin
or tCHmin
-
tCLmin
or tCHmin
-
tCLmin
or tCHmin
-
ns
Data hold skew factor
DQS write postamble time
tQHS
0.55
0.75
0.75
ns
tWPST
0.4
0.6
0.4
0.6
0.4
0.6
tCK
3
Active to Read with Auto precharge
command
tRAP
20
20
20
Autoprecharge write recovery +
Precharge time
tDAL
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
tCK 11
1. Maximum burst refresh cycle : 8
2. The specific requirement is that DQS be valid(High or Low) on or before this CK edge. The case shown(DQS going from
High_Z to logic Low) applies when no writes were previously in progress on the bus. If a previous write was in progress,
DQS could be High at this time, depending on tDQSS.
3. The maximum limit for this parameter is not a device limit. The device will operate with a great value for this parameter,
but system performance (bus turnaround) will degrade accordingly.
4. A write command can be applied with tRCD satisfied after this command.
5. For registered DIMMs, tCL and tCH are ≥ 45% of the period including both the half period jitter (t JIT(HP) ) of the PLL and the half period
jitter due to crosstalk (tJIT(crosstalk) ) on the DIMM.
6. Input Setup/Hold Slew Rate Derating
Input Setup/Hold Slew Rate
∆tIS
∆ tIH
(V/ns)
(ps)
(ps)
0.5
0
0
0.4
+50
+50
0.3
+100
+100
This derating table is used to increase t_IS/t_IH in the case where the input slew rate is below 0.5V/ns. Input setup/hold slew rate
based on the lesser of AC-AC slew rate and DC-DC slew rate.
7. I/O Setup/Hold Slew Rate Derating
I/O Setup/Hold Slew Rate
∆tDS
∆tDH
(V/ns)
(ps)
(ps)
0.5
0
0
0.4
+75
+75
0.3
+150
+150
This derating table is used to increase t_DS/t_DH in the case where the I/O slew rate is below 0.5V/ns. I/O setup/hold slew rate
based on the lesser of AC-AC slew rate and DC-DC slew rate.
Rev. 0.2 May. 2002