DS_M368L3223DTL Datasheet, PDF (8/12 Pages) Samsung semiconductor – 256MB DDR SDRAM MODULE

M368L3223DTL
184pin Unbuffered DDR SDRAM MODULE
AC Timming Parameters & Specifications (These AC charicteristics were tested on the Component)
Parameter
Symbol
-TCB3
(DDR333)
Min
Max
-TCA2
(DDR266A)
Min
Max
-TCB0
(DDR266B)
Min
Max
Unit Note
Row cycle time
tRC
60
65
65
ns
Refresh row cycle time
tRFC
72
75
75
ns
Row active time
tRAS
42
70K
45
120K
45
120K
ns
RAS to CAS delay
tRCD
18
20
20
ns
Row precharge time
tRP
18
20
20
ns
Row active to Row active delay
tRRD
12
15
15
ns
Write recovery time
tWR
15
15
15
ns
Last data in to Read command
tWTR
1
1
1
tCK
Col. address to Col. address delay
tCCD
1
1
1
tCK
Clock cycle time
CL=2.0
7.5
12
7.5
12
10
12
ns
5
tCK
CL=2.5
6
12
7.5
12
7.5
12
ns
5
Clock high level width
tCH
0.45
0.55
0.45
0.55
0.45
0.55
tCK
Clock low level width
tCL
0.45
0.55
0.45
0.55
0.45
0.55
tCK
DQS-out access time from CK/CK
tDQSCK
-0.6
+0.6
-0.75
+0.75
-0.75
+0.75
ns
Output data access time from CK/ CK
tAC
-0.7
+0.7
-0.75
+0.75
-0.75
+0.75
ns
Data strobe edge to ouput data edge
tDQSQ
-
0.45
-
0.5
-
0.5
ns
5
Read Preamble
tRPRE
0.9
1.1
0.9
1.1
0.9
1.1
tCK
Read Postamble
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
tCK
CK to valid DQS-in
tDQSS
0.75
1.25
0.75
1.25
0.75
1.25
tCK
DQS-in setup time
tWPRES
0
0
0
ns
2
DQS-in hold time
tWPRE
0.25
0.25
0.25
tCK
DQS falling edge to CK rising-setup time
tDSS
0.2
0.2
0.2
tCK
DQS falling edge from CK rising-hold time
tDSH
0.2
0.2
0.2
tCK
DQS-in high level width
tDQSH
0.35
0.35
0.35
tCK
DQS-in low level width
tDQSL
0.35
0.35
0.35
tCK
DQS-in cycle time
tDSC
0.9
1.1
0.9
1.1
0.9
1.1
tCK
Address and Control Input setup time(fast)
tIS
0.75
0.9
0.9
ns
6
Address and Control Input hold time(fast)
tIH
0.75
0.9
0.9
ns
6
Address and Control Input setup time(slow)
tIS
0.8
1.0
1.0
ns
6
Address and Control Input hold time(slow)
tIH
0.8
1.0
1.0
ns
6
Data-out high impedence time from CK/ CK
tHZ
-0.7
+0.7
-0.75
+0.75
-0.75
+0.75
ns
Data-out low impedence time from CK/ CK
tLZ
-0.7
+0.7
-0.75
+0.75
-0.75
+0.75
ns
Input Slew Rate(for input only pins)
tSL(I)
0.5
0.5
0.5
V/ns
6
Input Slew Rate(for I/O pins)
tSL(IO)
0.5
0.5
0.5
V/ns
7
Output Slew Rate(x4,x8)
tSL(O)
1.0
4.5
1.0
4.5
1.0
4.5
V/ns 1 0
Output Slew Rate Matching Ratio(rise to fall) tSLMR
0.67
1.5
0.67
1.5
0.67
1.5
Rev. 0.2 May. 2002