BU94605AKV Datasheet, PDF (51/84 Pages) Rohm – AAC/WMA/MP3 +SD Memory Card +CD-ROM+MP3 Record

BU94605AKV BU94607AKV BU94702AKV BU94705AKV
Datasheet
SET_LANG2
SET_OUTLANG
SET_TOUT_TUR
SET_IDL_TIME
SET_TUR_PASS
SET_THR1
SET_THR2
restart analysis.
4 0x60 0x11 0x00 N ・Set up the character encoding conversion mode inside a file system.
・Please choose N from the following values. The other setup is not
received.
N= 0x00 : Character encoding conversion is performed inside a file
system.
N= 0x01 : Character encoding conversion is not performed inside a file
system.
・When N= 0x01 is set up, an action changes as follows.
the path information which Read(s) -- the data in media -- it becomes
binary data as it is
The other delimiter and reservation character of path information turns
into a character of UTF-16 encoding.
・After a receptionist, when this command performs changes in system
mode, it becomes effective.
・Please use it as N=0x00 when changing to the operation modes other
than the PLAYER mode.
・An initial value is N= 0x00.
4 0x60 0x12 0x00 N ・Set up whether UTF8/UTF16 conversion is performed when the
character string status output of a file and a folder name.
・Please choose N from the following values. The other setup is not
received.
N= 0x00 : With a setup of SET_LANG, it outputs without changing.
N= 0x01 : It changes and outputs to UTF-8 at the time of an output.
N= 0x02 : It changes and outputs to UTF-16 at the time of an output.
・An initial value is N= 0x00.
4 0x60 0x18 0x01 N ・Set up the wait time after Test Unit Ready command transmission at the
time of USB memory recognition.
・When the response to Test Unit Ready is failure, re-try of Test Unit
Ready is performed after the setting value Nx2 (msec).
・Re-try is performed to 375 times.
・A timeout occurs after the setting value Nx750 (msec).
・An initial value is 191sec (setting value N=0xFF).
6 0x60 0x18 0x02 0x00 ・Set up the idle time after USB memory bus reset.
・Set a setup as the 5 - 6th byte with a little endian.
・Setting value {6th=M, 5th=N} x0.167 (usec) becomes wait time.
・As for an initial value, 220usec (setting value N=1325= {M=x05, N=x2D})
is set up.
・Please set a setting value as the range of 300 (50usec)-9000 (1.5msec).
4 0x60 0x18 0x0B N ・Operation after timeout generating with the Test Unit Ready command is
set up at the time of USB memory recognition.
・Please choose 4th byte N from the following. A setup of those other than
the following operates as that to which 0x01 was set.
N= 0x00: It is referred to as ERROR as memory recognition failure after
a timeout.
N= 0x01: When the number of effective LUN is one, after a timeout, the
response of Test Unit Ready is disregarded and the next memory
recognition processing is performed.
・An initial value is N= 0x00.
12 0x6F 0x00 0x00 0x00 ・Setup which performs the through output to I²S output from I²S input.
・Please set up 8 bytes from the 5th byte of following.
0x00 0x00 0x30 0xD0 0x1E 0x00 0x00 0x00
・When you perform a through output, please set up SET_THR1,
SET_THR2, and SET_THR3.
・When the operation mode was changed from the CD-DA mode and the
START_ENCODE command are issued, this setting is released.
12 0x6F 0x00 0x00 0x00 ・Setup which performs the through output to I²S output from I²S input.
・Please set up 8 bytes from the 5th byte of following.
Through output invalidity; 0x00 0x00 0xB0 0xD0 0x01 0x00 0x00 0x00
Through output effective; 0x00 0x00 0xB0 0xD0 0x05 0x00 0x00 0x00
・When you perform a through output, please set up SET_THR1,
SET_THR2, and SET_THR3.
・When the operation mode was changed from the CD-DA mode and the
START_ENCODE command are issued, this setting is released.
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
51/80
TSZ02201-0V2V0E600090-1-2
2012.12.10 Rev.002