XA-G39 Datasheet, PDF (32/42 Pages) NXP Semiconductors – XA 16-bit microcontroller family XA 16-bit microcontroller 32K FLASH/1K RAM, watchdog, 2 UARTs

Philips Semiconductors
XA 16-bit microcontroller family
32K Flash/1K RAM, watchdog, 2 UARTs
Preliminary data
XA-G39
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Operating temperature under bias
Storage temperature range
Voltage on EA/V_PP pin to V_SS
Voltage on any other pin to V_SS
Maximum I_OL per I/O pin
Power dissipation (based on package heat transfer limitations, not device power consumption)
RATING
–55 to +125
–65 to +150
0 to +13.0
–0.5 to V_DD+0.5 V
15
1.5
UNIT
°C
°C
V
V
mA
W
DC ELECTRICAL CHARACTERISTICS
V_DD = 4.5 V to 5.5 V; T_amb = 0 to +70 °C, unless otherwise specified.
V_DD = 4.75 V to 5.25 V; T_amb = –40 to +85 °C, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
UNIT
MIN
TYP
MAX
Supplies
I_DD
Supply current operating
5.25 V, 30 MHz
110
mA
I_ID
Idle mode supply current
5.25 V, 30 MHz
40
mA
I_PD
Power-down current
30
mA
I_PDI
Power-down current (–40 °C to +85 °C)
150
mA
V_RAM
RAM-keep-alive voltage
RAM-keep-alive voltage
1.5
V
V_IL
Input low voltage
–0.5
0.22 V_DD
V
V_IH
Input high voltage, except XTAL1, RST
At 5.0 V
2.2
V
V_IH1
Input high voltage to XTAL1, RST
At 5.0 V
0.8V_DD
V
V_IL1
Input low voltage to XATL1, RST
At 5.0 V
0.12 V_DD
V_OL
Output low voltage all ports, ALE, PSEN³
I_OL = 3.2mA, V_DD = 5.0 V
0.5
V
V_OH1
Output high voltage all ports, ALE, PSEN¹
I_OH = –100mA, V_DD = V_DDmin
2.4
V
V_OH2
Output high voltage, ports P0–3, ALE, PSEN²
I_OH = 3.2mA, V_DD = V_DDmin
2.4
V
C_IO
Input/Output pin capacitance
15
pF
I_IL
Logical 0 input current, P0–3⁶
V_IN = 0.45 V
–25
–75
mA
I_LI
Input leakage current, P0–3⁵
V_IN = V_IL or V_IH
±10
mA
I_TL
Logical 1 to 0 transition current all ports⁴
At 5.25 V
–650
mA
NOTES:
1. Ports in Quasi bi-directional mode with weak pull-up (applies to ALE, PSEN only during RESET).
2. Ports in Push-Pull mode, both pull-up and pull-down assumed to be same strength
3. In all output modes
4. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when
V_IN is approximately 2 V.
5. Measured with port in high impedance output mode.
6. Measured with port in quasi-bidirectional output mode.
7. Load capacitance for all outputs=80pF.
8. Under steady state (non-transient) conditions, I_OL must be externally limited as follows:
Maximum I_OL per port pin:
15mA (*NOTE: This is 85 °C specification for V_DD = 5 V.)
Maximum I_OL per 8-bit port:
26mA
Maximum total I_OL for all output: 71mA
If I_OL exceeds the test condition, V_OL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
2002 Mar 13
32