NOIL1SN3000A Datasheet, PDF (4/57 Pages) ON Semiconductor – MegaPixel High Speed CMOS Sensor

NOIL1SN3000A
Electrical Specifications
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 5. POWER SUPPLY RATINGS (Notes 1, 2 and 3)
Limits in bold apply for T_A = T_MIN to T_MAX, all other limits T_A = +25°C. System speed = 50 MHz, Sensor clock = 200 MHz
Symbol
Power Supply
Parameter
Condition
Min
Typ
Max
Units
V_ANA, GND_ANA Analog Supply
Operating Voltage
Dynamic Current
Clock enabled, lux = 0
-5%
2.5
+5%
V
35
mA
Peak Current
Row overhead time (ROT)
100
mA
V_DD, GND_DD
Digital Supply
Operating Voltage
Dynamic Current
Clock enabled, lux = 0
-5%
2.5
+5%
V
1
mA
Peak Current
Frame overhead time (FOT)
80
mA
V_{DD_HS},
GND_{DD_HS}
Digital Supply
high speed
Operating Voltage
Dynamic Current
Clock enabled, lux = 0
-5%
2.5
+5%
V
100
mA
Peak Current
FOT
60
mA
V_PIX, GND_PIX Pixel Supply
Operating Voltage
Peak Current during FOT Transient duration = 2 ms
-5%
2.5
+5%
V
210
mA
Peak Current during ROT Transient duration = 0.5 ms
100
mA
V_LVDS,
GND_LVDS
LVDS Supply
Operating Voltage
Dynamic Current
Clock enabled, lux = 0
-5%
2.5
+5%
V
170
mA
Peak Current
ROT
80
mA
V_ADC, GND_ADC ADC Supply
Operating Voltage
Dynamic Current
Clock enabled, lux = 0
-5%
2.5
+5%
V
150
mA
Peak Current
Clock enabled, lux = 0
275
mA
V_RES
Reset Supply
Operating Voltage
Peak current during FOT
Transient duration: 200 ns
-5%
3.3
+5%
V
1000
mA
V_{RES_DS}
Reset dual slope Operating Voltage
supply
1.8
2.5
3.5
V
V_{MEM_L}
(Note 4)
Memory Element Operating Voltage
low level supply
Peak current during FOT
Clock enabled, bright
-5%
2.5
+5%
V
180
mA
V_{MEM_H}
Memory Element Operating Voltage
high level supply
Peak current during FOT
-5%
3.3
+5%
V
90
mA
V_PRECHARGE
Pre_charge
Driver Supply
Operating Voltage
Peak Current during FOT Transient duration: 50 ns
-10%
0.4
+10%
V
10
mA
V_CM
Common mode Operating Voltage
(Refer to Table 44 on page 29)
0.9
V
voltage
1. All parameters are characterized for DC conditions after thermal equilibrium is established.
2. Peak currents are measured without the load capacitor from the LDO (Low Dropout Regulator). The 100 nF capacitor bank is connected
to the pin in question.
3. This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields. However, take normal
precautions to avoid application of any voltages higher than the maximum rated voltages to this high impedance circuit.
4. The V_{MEM_L} power supply should have a sourcing and sinking current capability.
Table 6. POWER DISSIPATION (Note 1)
Power supply specifications according to Table 5.
Symbol
Parameter
Dynamic Power Average power dissipation
Standby Power Power dissipation in standby
Condition
lux = 0, clock = 50 MHz
lux = 0, No clock
Min
Typ
Max Units
0.8
1.1
1.4
W
180
mW
http://onsemi.com
4