LC88F5LA4ACS Datasheet, PDF (28/33 Pages) Sanyo Semicon Device – FROM 96K byte, RAM 6K byte on-chip 16-bit 1-chip Microcontroller

LC88F5LA4ACS
Continued from preceding page.
Parameter
Symbol
Applicable
Pin/Remarks
Conditions
VDD[V]
min
HALT mode
consumption
current
(Note 7-1)
IDDHALT(1)
VDD1
=VDD2
=VDDA
≥VDD3
• HALT mode
• FmCF=10MHz ceramic oscillation mode
• FmMRC=0MHz (oscillation stoped)
• FmX'tal=32.768kHz crystal oscillation mode
• System clock set to 10MHz
2.6 to 3.6
• Internal RC oscillation stopped
• 1/1 frequency division mode
IDDHALT(2)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=10MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode 2.6 to 3.6
• System clock set to 10MHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
IDDHALT(3)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=4MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode 2.2 to 3.6
• System clock set to 4MHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
IDDHALT(4)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
2.2 to 3.6
• System clock set to internal RC oscillation
• 1/1 frequency division mode
IDDHALT(5)
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
2.2 to 3.6
• System clock set to 32.768kHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
HOLD mode
consumption
current
IDDHOLD(1)
VDD1
HOLD mode
• CF1=VDD or open (external clock mode)
2.2 to 3.6
Specification
typ
max unit
1.18
2.0
1.05
1.8
mA
0.44
0.8
0.12
0.5
8.21
40
μA
0.02
20
HOLDX
IDDHOLD(2)
HOLDX mode
mode
consumption
• CF1=VDD or open (external clock mode)
• FmX'tal=32.768kHz crystal oscillator mode
2.2 to 3.6
5.2
35
current
Note 7-1: The consumption current value includes none of the currents that flow into the output transistor and internal
pull-up resistors.
F-ROM Programming Characteristics at Ta = +10°C to +55°C, VSS1=VSS2=VSSA=0V
Parameter
Onboard
programming
current
Onboard
programming
time
Symbol
IDDFW(1)
Applicable
Pin/Remarks
VDD1
Conditions
• Microcontroller erase current current is
excluded.
tFW(1)
tFW(2)
• 128-/1K-byte erase operation
• 2-byte programming operation
VDD[V]
min
2.6 to 3.6
Specification
typ
max
unit
7 mA
2.6 to 3.6
2.6 to 3.6
30 ms
60 μs
No.A1860-28/33