E3X-MDA11 Datasheet, PDF (5/14 Pages) Omron Electronics LLC – OMRONs Next-generation Platform for a Wide Range of Detection

E3X-DA-S/MDA
Ratings and Specifications
Refer to pages 17 to 20 for dimensions.
Amplifier Units
Type
Single-function
models
Standard
models
Mark-detecting models (multiple color light sources)
Green LED
Blue LED
Infrared LED
Item
Model E3X-DA@SE-S
E3X-DA@-S
E3X-DAG@-S
E3X-DAB@-S
E3X-DAH@-S
Light source (wavelength) Red LED (635 nm)
Green LED (525 nm) Blue LED (470 nm) Infrared LED (870nm)
Power supply voltage
12 to 24 VDC ±10%, ripple (p-p) 10% max.
Power consumption
960 mW max. (current consumption: 40 mA max. at power supply voltage of 24 VDC)
Control output
Load power supply voltage: 26.4 VDC; NPN/PNP open collector;
load current: 50 mA max.; residual voltage: 1 V max.
Protection circuits
Reverse polarity for power supply connection, output short-circuit
Super-high-speed mode
---
Operate: 48 μs, reset: 50 μs *1, *2
Response ^{High-speed mode}
---
Operate/reset: 250 μs
time
Standard mode Operate or reset: 1 ms
High-resolution mode
---
Operate or reset: 4 ms
Sensitivity setting
Teaching or manual method
Power tuning
---
Light emission power and reception gain, digital control method
Timer function
Select from OFF-delay, ON-delay, or one-shot timer.
---
1 ms to 5 s (1 to 20 ms set in 1-ms increments, 20 to 200 ms set in 10-ms increments,
200 ms to 1 s set in 100-ms increments, and 1 to 5 s set in 1 s-increments)
Functions
Automatic power
control (APC)
High-speed control method for emission current
Zero-reset
---
Negative values can be displayed. (Threshold value is shifted.)
Initial reset
Settings can be returned to defaults as required.
Mutual interfer-
ence prevention
Possible for up to 10 Units *3
Display
Operation indicator
(orange)
Operation indicator (orange), Power Tuning indicator (orange)
Digital display
incident level +
threshold
Select from incident level + threshold or other 6 patterns
Display orientation
---
Switching between normal/reversed display is possible.
Ambient illumination
(Receiver side)
Ambient temperature range
Ambient humidity range
Insulation resistance
Incandescent lamp: 10,000 lux max.
Sunlight:
20,000 lux max.
Operating: Groups of 1 to 2 Amplifiers: −25°C to 55°C
Groups of 3 to 10 Amplifiers: −25°C to 50°C
Groups of 11 to 16 Amplifiers: −25°C to 45°C
Storage: −30°C to 70°C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
20 MΩ min. (at 500 VDC)
Dielectric strength
1,000 VAC at 50/60 Hz for 1 minute
Vibration resistance
Shock resistance
Destruction: 10 to 55 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions
Destruction: 500 m/s², for 3 times each in X, Y and Z directions
Degree of protection
IEC 60529 IP50 (with Protective Cover attached)
Connection method
Pre-wired or amplifier unit connector
Weight (packed state)
Pre-wired model: Approx. 100 g, Amplifier unit connector model: Approx. 55 g
Case
Materials
Cover
Polybutylene terephthalate (PBT)
Polycarbonate (PC)
Accessories
Instruction manual
*1. Communications are disabled if the detection mode is selected during super-high-speed mode, and the communications functions for mutual interference prevention
and the Mobile Console will not function.
*2. PNP output is as follows: Operate: 53 μs, reset: 55 μs.
*3. Mutual interference prevention can be used for only up to 6 Units if power tuning is enabled.
5