E3T-FD11M Datasheet, PDF (4/24 Pages) Omron Electronics LLC – The Improved E3T Series with Easier, Smoother Mounting and Installation

E3T
Accessories (Order Separately)
Accessories for M2-mounting Sensors These accessories are not included with the Sensor. Order them separately if required.
Name
Applicable
Sensor
Model
Quantity
Dimensions
page
Remarks
Mutual Interference Prevention Filter for
Through-beam Side-view Sensors ^*1
E3T-ST3@
E3T-ST1@
E39-E14
4
(Two each for Emitter
and Receiver)
Sensing distance 1 m
Sensing distance 0.5 m
E3T-ST3@
0.5 dia. E3T-ST1@
Slit for Through-beam
Side-view Sensors
E3T-ST2@
E3T-ST3@
1 dia. E3T-ST1@
E3T-ST2@
Slit for Through-beam Flat
Sensors
0.5 dia.
E3T-FT1@
E3T-FT2@
1 dia.
E3T-FT1@
E3T-FT2@
Sensitivity Adjustment Unit for Through-
beam Side-view Sensors
E3T-ST3@
E3T-ST1@
Mounting Brackets for Side-view Sensors
*2
E3T-S@@@
Mounting Brackets for Flat Sensors ^*2 E3T-F@@@
Screw Set for Side-view Sensors ^*3*4
E3T-S@@@
E39-S63
E39-S64
E39-E10
E39-L116
E39-L117
E39-L118
E39-L119
E39-L120
E39-L164
Screw Set for Flat Sensors ^*3*4
E3T-F@@@
E39-L165
2
(One each for Emitter
and Receiver; common
with Slit widths of 1 dia.
and 0.5 dia.)
1
1
2 for each
Sensing distance 200 mm,
Minimum detectable object (typical)
0.5-mm dia.
Sensing distance 100 mm,
Minimum detectable object (typical)
0.5-mm dia.
Sensing distance 30 mm,
Minimum detectable object (typical)
0.5-mm dia.
Sensing distance 600 mm,
Minimum detectable object (typical)
1-mm dia.
Sensing distance 300 mm,
Minimum detectable object (typical)
1-mm dia.
19
Sensing distance 100 mm,
Minimum detectable object (typical)
1-mm dia.
Sensing distance 50 mm,
Minimum detectable object (typical)
0.5-mm dia.
Sensing distance 30 mm,
Minimum detectable object (typical)
0.5-mm dia.
Sensing distance 100 mm,
Minimum detectable object (typical)
1-mm dia.
Sensing distance 50 mm,
Minimum detectable object (typical)
1-mm dia.
Sensing distance (typical) 1,200 to
1,800 mm
Sensing distance (typical) 300 to
800 mm
20
Nut plate provided
21
---
Material: Iron (Same type as provided
with the Sensor.)
Contents: Phillips screws (M2×14),
Hexagonal nuts, Spring washers, Flat
washers
Material: Iron (Same type as provided
with the Sensor.)
Contents: Phillips screws (M2×8),
Hexagonal nuts, Spring washers, Flat
---
washers
SUS Screw Set for Flat Sensors ^*3
E3T-F@@@
E39-L172
2
Material: SUS304
Contents: Bolt with hexagonal hole
(M2×6)
SUS Screw Set for Side-view Sensors ^*3 E3T-S@@@
E39-L173
2 for each
Material: SUS304
Contents: Bolt with hexagonal hole
(M2×12), Hexagonal nuts, Spring
washers, Flat washers
*1.An arrow indicates the polarization direction. Mutual interference can be prevented by using different polarization directions for adjacent Emitters/Receivers.
*2. When using Through-beam Sensors (E3T-ST@@, E3T-FT@@), order one bracket for the Emitter and one for the Receiver.
*3. Order two Sets, one for the Emitter and one for the Receiver, for Through-beam Sensors (E3T-ST@@ or E3T-FT@@).
This is the Screw Set for mounting the Sensor to the Mounting Bracket. Order this Set if you loose the screws. Do not use this Screw Set to mount the Mounting
Bracket to the equipment.
*4. This is included with the Sensor.
4