D2SW-P Datasheet, PDF (4/8 Pages) Omron Electronics LLC – Sealed Subminiature Basic Switch

■ Dimensions and Operating Characteristics
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2. The following illustrations and drawings are for solder terminal models. Refer to Terminals section for details on models with quick-connect
terminals (#110) or PCB terminals or molded lead wires.
3. The operating characteristics are for operation in the A direction ( ).
.
Pin Plunger Models
D2SW-P2@@
D2SW-P01@@
A
PT
2.5±^0.07 dia.
7.55±0.2
1.8 dia.
2.35
+0.075
−0.05
dia.
OP
2.35⁺_{−00..00575} ^7.3
3.2
2.15
8.55
15.5
5.15 9.5±^0.1
19.8±^0.2
6.9 7.7
3.3±^0.1
Three, 1.6 dia. holes
0.5
6.4±^0.2
OF max.
RF min.
PT max.
OT min.
MD max.
OP
183 gf
20 gf
0.6 mm
0.4 mm
0.15 mm
8.4±0.3 mm
Hinge Lever Models
D2SW-P2L1@@
D2SW-P01L1@@
A
t=0.3 Stainless-steel lever
2.5±^0.07 dia.
14.5±0.6
2.35
+0.075
−0.05
dia.
2.35⁺_{−00..00575}
7.3
6.9 7.7 ^{OP FP}
3.3±0.1
3.2
2.15
8.55
15.5
5.15 9.5±^0.1
19.8±^0.2
Three, 1.6 dia. holes
0.5
6.4±^0.2
Hinge Roller Lever Models
D2SW-P2L2@@
D2SW-P01L2@@
t=0.3 Stainless-steel lever
A
14.5±0.6
dia. 4.8 x 3.2
Polyacetal resin roller
2.5±0.07 dia.
2.35
+0.075
-0.05
7.3
2.35
+0.075
-0.05
dia.
OP
FP
6.9 ^7.7
3.3±0.1
3.2
2.15
8.55
15.5
5.15 9.5±^0.1
19.8±0.2
Three, 1.6 dia. holes
0.5
6.4±^0.2
Simulated Roller Lever Models
D2SW-P2L3@@
D2SW-P01L3@@
t=0.3 Stainless-steel lever
2.5±^0.07 dia.
2.35
+0.075
−0.05
7.3
A
15.8±^0.6
R1.3
2.35
+0.075
−0.05
dia.
OP ^FP
6.9 7.7
3.3±0.1
3.2
2.15
8.55
15.5
5.15 9.5±^0.1
19.8±0.2
Three, 1.6 dia. holes
0.5
6.4±0.2
OF max.
RF min.
OT min.
MD max.
FP max.
OP
61 gf
5 gf
0.8 mm
0.8 mm
13.6 mm
8.8±0.8 mm
OF max.
RF min.
OT min.
MD max.
FP max.
OP
61 gf
5 gf
0.8 mm
0.8 mm
19.3 mm
14.5±0.8 mm
OF max.
RF min.
OT min.
MD max.
FP max.
OP
61 gf
5 gf
0.8 mm
0.8 mm
15.5 mm
10.7±0.8 mm
204
Sealed Subminiature Basic Switch D2SW-P