D2SW-P Datasheet, PDF (2/8 Pages) Omron Electronics LLC – Sealed Subminiature Basic Switch

Specifications
■ Characteristics
Item
Model
D2SW-P2
D2SW-P01
Operating speed
0.1 mm to 500 mm/s (pin plunger models)
Operating frequency
Mechanical: 120 operations/min max.
Electrical: 20 operations/min max.
Insulation resistance
100 MΩ min. (at 500 VDC)
Contact resistance
Terminal models: 50 mΩ max.
Molded lead wire models: 100 mΩ max.
Terminal models: 100 mΩ max.
Molded lead wire models: 150 mΩ max.
Dielectric strength (see note 2)
1,000 VAC, 50/60 Hz for 1 min. between
terminals of the same polarities
600 VAC, 50/60 Hz for 1 min. between
terminals of the same polarities
1,500 VAC, 50/60 Hz for 1 min. between current-carrying metal parts and ground, and between
each terminal and non-current-carrying metal parts
Vibration resistance (see note 3)
Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance (see note 3)
Destruction: 1,000 m/s² (approx. 100 G) max.
Malfunction: 300 m/s² (approx. 30 G) max.
Degree of protection
IEC IP67 (excluding the terminals on terminal models)
Degree of protection against electric shock Class I
Proof tracking index (PTI)
175
Ambient operating temperature
-20°C to 70°C (at 60% RH max.) with no icing
Ambient operating humidity
85% max. (for 5°C to 35°C)
Life expectancy
Mechanical: 1,000,000 operations min.
(60 operations/min.)
Mechanical: 1,000,000 operations min.
(60 operations/min.)
Electrical: 50,000 operations min.
(20 operations/min.)
Electrical: 200,000 operations min.
(20 operations/min.)
Weight
Approx. 2 g (pin plunger models with terminals)
Note: 1. The data given above are initial values.
2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate.
3. For the pin plunger models, the above values apply for both the free position and total travel position. For the lever models, the values
apply at the total travel position. Contact opening or closing time is within 1ms.
■ Ratings
■ Contact Specifications
Model
D2SW-P2
D2SW-P01
Rated voltage
30 VDC
250 VAC
30 VDC
125 VAC
Resistive load
2A
0.1 A
Note: The ratings values apply under the following test conditions.
Ambient temperature: 20±2°C
Ambient humidity: 65±5%
Operating frequency: 20 operations/min.
■ Approved Standards
UL Recognized
CSA Certified
Rated voltage
125 VAC
250 VAC
30 VDC
D2SW-P2
—
2A
2A
D2SW-P01
0.1 A
—
0.1 A
Item
Specification
Material
Gap (standard value)
Minimum applicable load
(see note)
D2SW-P2
Rivet
Silver alloy
0.5 mm
160 mA at 5 VDC
D2SW-P01
Crossbar
Gold alloy
1 mA at 5 VDC
Note: Minimum applicable loads are indicated by N standard refer-
ence values. This value represents the failure rate at a 60%
(_Tλ_h6e0)erqeuliaatbioilnity_λ6le₀v=e0l.(5JxIS1C0_-5₆0/0o3p)e. _{rations indicates that a failure}
rate of 1/2,000,000 operations can be expected at a reliability
level of 60%
■ Contact Form
SPDT
SPST-NC
SPST-NO
(wire models, only) (wire models, only)
COM NO NC
(Black) (Blue) (Red)
COM
(Black)
NC
(Red)
COM NO
(Black) (Blue)
Note: Lead wire colors are indicated in parentheses.
202
Sealed Subminiature Basic Switch D2SW-P