DS92LV010A Datasheet, PDF (3/10 Pages) National Semiconductor (TI) – Bus LVDS 3.3/5.0V Single Transceiver

DC Electrical Characteristics (Notes 2, 3) (Continued)
T_A = −40˚C to +85˚C unless otherwise noted, V_CC = 3.3V ± 0.3V
Symbol
Parameter
Conditions
C_output
Capacitance @ BUS
Pins
Pin
Min
DO+/RI+,
DO−/RI−
Typ Max Units
5
pF
DC Electrical Characteristics (Notes 2, 3)
T_A = −40˚C to +85˚C unless otherwise noted, V_CC = 5.0V ± 0.5V
Symbol
Parameter
Conditions
V_OD
Output Differential
Voltage
R_L = 27Ω, Figure 1
∆V_OD
V_OS
∆V_OS
V_OD Magnitude Change
Offset Voltage
Offset Magnitude
Change
I_OSD
Output Short Circuit
Current
V_O = 0V, DE = V_CC
V_OH
Voltage Output High
V_ID = +100 mV
Inputs Open
I_OH = −400 µA
Inputs Shorted
V_OL
Voltage Output Low
I_OS
Output Short Circuit
Current
Inputs
Terminated, R_L = 27Ω
I_OL = 2.0 mA, V_ID = −100 mV
V_OUT = 0V, V_ID = +100 mV
V_TH
Input Threshold High
V_TL
Input Threshold Low
I_IN
Input Current
V_IH
Minimum Input High
Voltage
DE = 0V
DE = 0V, V_IN = +2.4V, or 0V
V_CC = 0V, V_IN = +2.4V, or 0V
V_IL
Maximum Input Low
Voltage
I_IH
Input High Current
I_IL
Input Low Current
V_CL
Input Diode Clamp
Voltage
V_IN = V_CC or 2.4V
V_IN = GND or 0.4V
I_CLAMP = −18 mA
I_CCD
I_CCR
I_CCZ
I_CC
C_output
Power Supply Current
Capacitance @ BUS
Pins
DE = RE = V_CC, R_L = 27Ω
DE = RE = 0V
DE = 0V, RE = V_CC
DE = V_CC , RE = 0V, R_L = 27Ω
Pin
Min
DO+/RI+, 145
DO−/RI−
1
R_OUT
4.3
4.3
4.3
4.3
−35
DO+/RI+,
DO−/RI− _−100
−20
−20
DIN,
DE,
RE
2.0
GND
V _CC
−1.5
DO+/RI+,
DO−/RI−
Typ Max Units
270 390 mV
3
30 mV
1.35 1.65
V
5
50 mV
−12 −20 mA
5.0
V
5.0
V
5.0
V
5.0
V
0.1 0.4
V
−90 −130 mA
+100 mV
mV
±1 +20 µA
±1 +20 µA
V_CC
V
0.8
V
±1 ±10 µA
±1 ±10 µA
−0.8
V
17 25 mA
6
10 mA
3
8
mA
20 25 mA
5
pF
Note 1: “Absolute Maximum Ratings” are these beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should
be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground except V_OD, V_ID, V_TH and
V_TL unless otherwise specified.
Note 3: All typicals are given for V_CC = +3.3V or 5.0 V and T_A = +25˚C, unless otherwise stated.
Note 4: ESD Rating: HBM (1.5 kΩ, 100 pF) > 2.0 kV EAT (0Ω, 200 pF) > 300V.
Note 5: C_L includes probe and fixture capacitance.
Note 6: Generator waveforms for all tests unless otherwise specified: f = 1MHz, ZO = 50Ω, tr, tf ≤ 6.0ns (0%–100%) on control pins and ≤ 1.0ns for RI inputs.
Note 7: The DS92LV010A is a current mode device and only function with datasheet specification when a resistive load is applied between the driver outputs.
Note 8: For receiver TRI-STATE^® delays, the switch is set to V_CC for t_PZL, and t_PLZ and to GND for t_PZH, and t_PHZ.
3
www.national.com