|
DS90CR218A_06 Datasheet, PDF (3/11 Pages) National Semiconductor (TI) – +3.3V Rising Edge Data Strobe LVDS 21-Bit Channel Link - 12 MHz to 85 MHz | |||
|
◁ |
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (VCC)
CMOS/TTL Input Voltage
CMOS/TTL Output Voltage
LVDS Receiver Input Voltage
Junction Temperature
â0.3V to +4V
â0.5V to (VCC + 0.3V)
â0.3V to (VCC + 0.3V)
â0.3V to (VCC + 0.3V)
+150ËC
Storage Temperature Range
â65ËC to +150ËC
Lead Temperature
(Soldering, 4 sec.)
+260ËC
Maximum Package Power Dissipation @ +25ËC
MTD48 (TSSOP) Package:
DS90CR218A
1.89 W
Package Derating
DS90CR218A
ESD Rating
(HBM, 1.5kâ¦, 100pF)
(EIAJ, 0â¦, 200pF)
Latch Up Tolerance @ 25ËC
15 mW/ËC above +25ËC
> 7kV
> 700V
> ±300mA
Recommended Operating
Conditions
Supply Voltage (VCC)
Operating Free Air
Temperature (TA)
Receiver Input Range
Supply Noise Voltage (VCC)
Min Nom Max Units
3.0 3.3 3.6 V
â10 +25 +70 ËC
0
2.4 V
100 mVPP
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
Parameter
Conditions
CMOS/TTL DC SPECIFICATIONS
VIH
High Level Input Voltage
VIL
Low Level Input Voltage
VOH
High Level Output Voltage
VOL
Low Level Output Voltage
VCL
Input Clamp Voltage
IIN
Input Current
IOS
Output Short Circuit Current
LVDS RECEIVER DC SPECIFICATIONS
IOH = â0.4 mA
IOL = 2 mA
ICL = â18 mA
VIN = 0.4V, 2.5V or VCC
VIN = GND
VOUT = 0V
VTH
Differential Input High Threshold
VTL
Differential Input Low Threshold
IIN
Input Current
RECEIVER SUPPLY CURRENT
VCM = +1.2V
VIN = +2.4V, VCC = 3.6V
VIN = 0V, VCC = 3.6V
ICCRW
Receiver Supply Current Worst
Case
CL = 8 pF,
Worst Case
Pattern
(Figures 1, 2)
f = 33 MHz
f = 40 MHz
f = 66 MHz
f = 85 MHz
ICCRZ
Receiver Supply Current Power
Down
PWR DWN = Low
Receiver Outputs Stay Low during
Powerdown Mode
Min
2.0
GND
2.7
â10
â100
Typ
3.3
0.06
â0.79
+1.8
0
â60
49
53
78
90
140
Max Units
VCC
V
0.8
V
V
0.3
V
â1.5
V
+15
µA
µA
â120 mA
+100 mV
mV
±10
µA
±10
µA
60
mA
65
mA
100
mA
115
mA
400
µA
Note 1: âAbsolute Maximum Ratingsâ are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The tables of âElectrical Characteristicsâ specify conditions for device operation.
Note 2: Typical values are given for VCC = 3.3V and TA = +25ËC.
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise
specified (except VOD and âVOD).
3
www.national.com
|
▷ |