THS4511-SP Datasheet, PDF (21/25 Pages) Texas Instruments – RAD-TOLERANT CLASS V, WIDEBAND, FULLY DIFFERENTIAL AMPLIFIER

THS4511–SP
www.ti.com
SLOS538A – SEPTEMBER 2007 – REVISED OCTOBER 2007
Table 5. THS4511RGT EVM Bill of Materials
ITEM
DESCRIPTION
1 CAP, 10.0 μF, Ceramic, X5R, 6.3V
2 CAP, 0.1 μF, Ceramic, X5R, 10V
3 CAP, 0.22 μF, Ceramic, X5R, 6.3V
4 OPEN
5 OPEN
6 Resistor, 49.9 Ω, 1/16W, 1%
7 Resistor, 56.2 Ω, 1/16W, 1%
8 Resistor, 69.8 Ω, 1/16W, 1%
9 Resistor, 86.6 Ω, 1/16W, 1%
10 Resistor, 340 Ω, 1/16W, 1%
11 Resistor, 348 Ω, 1/16W, 1%
12 Resistor, 0 Ω, 5%
13 Transformer, RF
14
Jack, banana receptance, 0.25" diameter
hole
15 OPEN
16 Connector, edge, SMA PCB Jack
17 Test point, Red
18 IC, THS4511
19 Standoff, 4-40 HEX, 0.625" length
20 SCREW, PHILLIPS, 4-40, 0.250"
21 Printed circuit board
SMD
SIZE
0805
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0805
REFERENCE
DESIGNATOR
C3, C5
C11, C12, C13, C14
C15
C1, C2, C7, C8, C9, C10
R9, R10
R12
R1, R2
R11
R7, R8
R3, R4
R5, R6
C4, C6
T1
J5, J6
J1, J7, J8
J2, J3
TP1, TP2, TP3
U1
PCB
QTY
2
4
1
6
2
1
3
2
2
2
2
1
2
3
2
3
1
4
4
1
MANUFACTURER'S
PART NUMBER⁽¹⁾
(AVX) 08056D106KAT2A
(AVX) 0402ZD104KAT2A
(AVX) 04026D224KAT2A
(KOA) RK73H1ETTP49R9F
(KOA) RK73H1ETTP56R2F
(KOA) RK73H1ETTP69R8F
(KOA) RK73H1ETTP86R6F
(KOA) RK73H1ETTP3400F
(KOA) RK73H1ETTP3480F
(KOA) RK73Z2ATTD
(MINI-CIRCUITS) ADT1-1WT
(HH SMITH) 101
(JOHNSON) 142-0701-801
(KEYSTONE) 5000
(TI) THS4511RGT
(KEYSTONE) 1808
SHR-0440-016-SN
(TI) EDGE# 6475513
(1) The manufacturer's part numbers were used for test purposes only.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input and output voltage ranges as specified in the following table.
Input Range, V_S+ to V_S-
Input Range, V_I
Output Range, V_O
3.0 V to 6.0 V
3.0 V to 6.0 V NOT TO EXCEED V_S+ or V_S-
3.0 V to 6.0 V NOT TO EXCEED V_S+ or V_S-
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If
there are questions concerning the input range, please contact a TI field representative prior to connecting the
input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible
permanent damage to the EVM. Please consult the product data sheet or EVM user's guide (if user's guide is
available) prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 30°C. The EVM is
designed to operate properly with certain components above 50°C as long as the input and output ranges are
maintained. These components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors. These types of devices can be identified using the EVM schematic
located in the material provided. When placing measurement probes near these devices during operation, please
be aware that these devices may be very warm to the touch.
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): THS4511–SP
Submit Documentation Feedback
21