PTGL09BD2R2N2B51B0 Datasheet, PDF (88/103 Pages) Murata Manufacturing Co., Ltd. – PTC Thermistors for Overcurrent Protection / for Inrush Current Suppression / for Overheat Sensing Lead Type

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Temperature Sensor Lead Type Specifications and Test Methods
R90E.pdf
Sep.24,2012
No.
Item
1 Resistance Value
2 Withstanding Voltage
3
Tensile Strength of
Lead Wire Terminal
4
Bending Strength of
Lead Wire Terminal
5 Solderability
6
Terminal Durability of
Soldering
7 Damp Heat
8 High Temperature Load
Rating Value
Satisfies specification
No problem
No damage
Lead wire does not come off.
Solder is applied around the lead wire covering
3/4 or more of the circumference without gap in
the axial-direction.
ΔR/R25VT15%
ΔR/R25VT20%
ΔR/R25VT20%
PTH
Rs
S.W
Test circuit
Method of Examination
Resistance value is measured by applying voltage under 1.5Vdc
(by a direct current of less than 10mA) in a silicone oil vessel.
We apply AC voltage 120% that of the maximum voltage to
POSISTORr by raising voltage gradually for 180±5 seconds at
25°C. (A protective resistor is to be connected in series, and the
inrush current through POSISTORr must be limited below max.
rated value.)
The load is gradually applied to each terminal of POSISTORr
until 4.90N in the axial-direction with fixing POSISTORr's body
itself and this load is kept for 10 seconds.
POSISTORr is held so that it is perpendicular to the lead wire
with the following load hanging in the axial direction of the lead
wire. The lead wire is slowly bent to 90° and returned; then it is
slowly bent in the opposite direction and returned to original state.
(Above mentioned procedure is done slowly with one cycle.)
Series
PTFL
PTFM
Force
2.45N
4.90N
The lead wire of POSISTORr is soaked in a Isopropyl Alcohol
(JIS K 8839) or ethanol (JIS K 8101) solution (about 25wt%) of
colophony (JIS K 5902) for 5-10 sec. And, each lead wire is
soaked in molten solder (JIS Z 3282 H60A) at 235±5°C from the
bottom to a point of 2.0-2.5mm for 2±0.5 seconds.
The lead wire of POSISTORr is soaked in molten solder (JIS Z
3282 H60A) at 350±10°C from the bottom to a point of 2.0-2.5
mm for 3.5±0.5 seconds. And, after the device is left at room
temperature (25°C) for 24±4 hours, the resistance is measured.
POSISTORr is set in an environmental chamber at 40±2°C
and 90-95% humidity for 500±4 hours.
And after the device is left at room temperature (25°C) for one
hour, the resistance measurement is performed.
POSISTORr is set in an environmental chamber at 85±3°C with
maximum voltage applied for 1.5 hours and then is left without
voltage applied for 0.5 hours.
This cycle is repeated for 1000±10 hours, and after the device is
left at room temperature (25°C) for one hour, the resistance
measurement is performed.
(A protective resistor is to be connected in series and the inrush
current through POSISTORr must be limited below max. rated
value.)
14
86