PTGL09BD2R2N2B51B0 Datasheet, PDF (68/103 Pages) Murata Manufacturing Co., Ltd. – PTC Thermistors for Overcurrent Protection / for Inrush Current Suppression / for Overheat Sensing Lead Type

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
PTGL Series Specifications and Test Methods
R90E.pdf
Sep.24,2012
Item
Continuous Operating
Temperature
-10 to +60 °C
Rating Value
Resistance Value
(at 25°C)
Satisfies ratings
Withstanding Voltage No problem
Tensile Strength of
Lead Wire Terminal
No damage
Bending Strength of
Lead Wire Terminal
Lead wire does not come off.
Solderability
Solder is applied around the lead wire covering 3/4 or more of
the circumference without gap in the axial direction.
Terminal Durability
of Soldering
ΔR/R25^<=±15%
Humidity Test
ΔR/R25^<=±20%
Load Cycle Test at
High Temperature
ΔR/R25^<=±20%
Method of Examination
The temperature range with maximum voltage applied to the
POSISTORr.
Resistance value is measured by applying voltage under
1.5Vdc (by a direct current of less than 10mA) at 25°C.
But it must be measured after maximum voltage is applied for
180 seconds and then is left for 2 hours at 25°C.
As for 16V series, measurement probes should be connected
on the lead wire at the point within 2mm from the below side of
the forming.
Resistance should be measured by 4 wiring method.
We apply AC voltage 120% (16V Series: 110%) that of the
maximum voltage to POSISTORr by raising voltage gradually
for 180±5 seconds at 25°C. (A protective resistor is to be
connected in series, and the inrush current through
POSISTORr must be limited below max. rated value.)
The load is gradually applied to each terminal of POSISTORr
until the force of the following table in the axial direction with
fixing POSISTORr's body itself and this load is being kept for
10 seconds.
Lead Diameter
ø0.60mm max.
ø0.65mm min.
Force
4.90N
9.80N
POSISTORr is held so that it is perpendicular to the lead wire
with the following lead hanging in the axial direction of the lead
wire. The lead wire is slowly bent to 90° and returned. Then it is
slowly bent in the opposite direction and returned to original
state.
Lead Diameter
ø0.60mm max.
ø0.65mm min.
Force
2.45N
4.90N
The Lead wire of POSISTORr is soaked in an Isopropyl alcohol
(JIS K 8839) or ethanol (JIS K 8101) solution (about 25wt%) of
colophony (JIS K 5902) for 5 to 10 sec. And, each lead wire is
soaked in molten solder (JIS Z 3282 H60A) at 235±5°C from
the bottom to a point of 2.0 to 2.5mm for 2±0.5 sec.
The lead wire of POSISTORr is soaked in molten solder (JIS Z
3282 H60A) at 350±10°C from the bottom to a point of 2.0 to
2.5mm for 3.5±0.5 sec. After the device is being left at room
temperature (25°C) for 24±4 hours, the resistance is measured.
POSISTORr is set in an environmental chamber at 40±2°C
and 90 to 95% humidity for 500±4 hours. After the device is left
at room temperature (25°C) for one hour, the resistance
measurement is performed.
POSISTORr is set in an environmental chamber at 60±3°C
with maximum voltage applied for 1.5 hours and then is left
without voltage applied for 0.5 hours. This cycle is repeated for
1000±10 hours, and after the device is left at room temperature
(25°C) for one hour, the resistance measurement is performed.
(A protective resistor is to be connected in series and the
inrush current through POSISTORr must be limited below
max. rated value.)
66