MLP1N06CL Datasheet, PDF (6/6 Pages) Motorola, Inc – VOLTAGE CLAMPED CURRENT LIMITING MOSFET

MLP1N06CL
TYPICAL APPLICATIONS: INJECTOR DRIVER, SOLENOIDS, LAMPS, RELAY COILS
The MLP1N06CL has been designed to allow direct inter-
VBAT
face to the output of a microcontrol unit to control an isolated
load. No additional series gate resistance is required, but a
VDD
40 kΩ gate pulldown resistor is recommended to avoid a
floating gate condition in the event of an MCU failure. The in-
ternal clamps allow the device to be used without any exter-
D
nal transistent suppressing components.
G
MCU
MLP1N06CL
S
PACKAGE DIMENSIONS
Q
H
Z
B
4
1 23
F
T
–T–
SEATING
PLANE
C
S
A
U
K
STYLE 5:
PIN 1.
2.
3.
4.
GATE
DRAIN
SOURCE
DRAIN
L
V
G
D
N
R
J
CASE 221A–06
ISSUE Y
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
INCHES
DIM MIN MAX
A 0.570 0.620
B 0.380 0.405
C 0.160 0.190
D 0.025 0.035
F 0.142 0.147
G 0.095 0.105
H 0.110 0.155
J 0.018 0.025
K 0.500 0.562
L 0.045 0.060
N 0.190 0.210
Q 0.100 0.120
R 0.080 0.110
S 0.045 0.055
T 0.235 0.255
U 0.000 0.050
V 0.045 –––
Z ––– 0.080
MILLIMETERS
MIN MAX
14.48 15.75
9.66 10.28
4.07 4.82
0.64 0.88
3.61 3.73
2.42 2.66
2.80 3.93
0.46 0.64
12.70 14.27
1.15 1.52
4.83 5.33
2.54 3.04
2.04 2.79
1.15 1.39
5.97 6.47
0.00 1.27
1.15 –––
––– 2.04
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [e-mail] – TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
6
◊
*MLP1N06CL/D* ^{Motorola TMOS Power MOSFET TransisMtoLrPD1eNv0ic6eCLD/Data}