MTB23P06E Datasheet, PDF (1/10 Pages) Motorola, Inc – TMOS POWER FET 23 AMPERES 60 VOLTS

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document
by MTB23P06E/D
™ Designer's Data Sheet
TMOS E-FET.™
High Energy Power FET
D2PAK for Surface Mount
P–Channel Enhancement–Mode Silicon Gate
The D2PAK package has the capability of housing a larger die
than any existing surface mount package which allows it to be used
in applications that require the use of surface mount components
with higher power and lower RDS(on) capabilities. This advanced
TMOS E–FET is designed to withstand high energy in the
avalanche and commutation modes. The new energy efficient
design also offers a drain–to–source diode with a fast recovery
time. Designed for low voltage, high speed switching applications in
power supplies, converters and PWM motor controls, these
devices are particularly well suited for bridge circuits where diode
speed and commutating safe operating areas are critical and offer
additional safety margin against unexpected voltage transients.
• Avalanche Energy Specified
• Source–to–Drain Diode Recovery Time Comparable to a
G
Discrete Fast Recovery Diode
• Diode is Characterized for Use in Bridge Circuits
• IDSS and VDS(on) Specified at Elevated Temperature
• Short Heatsink Tab Manufactured — Not Sheared
• Specially Designed Leadframe for Maximum Power Dissipation
• Available in 24 mm 13–inch/800 Unit Tape & Reel, Add T4
Suffix to Part Number
®
D
S
MTB23P06E
Motorola Preferred Device
TMOS POWER FET
23 AMPERES
60 VOLTS
RDS(on) = 0.12 OHM
CASE 418B–02, Style 2
D2PAK
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
Drain–to–Source Voltage
VDSS
60
Vdc
Drain–to–Gate Voltage (RGS = 1.0 MΩ)
Gate–to–Source Voltage — Continuous
VDGR
60
Vdc
VGS
± 20
Vdc
Drain Current — Continuous
Drain Current — Continuous @ 100°C
Drain Current — Single Pulse (tp ≤ 10 µs)
ID
23
Adc
ID
14
IDM
75
Apk
Total Power Dissipation
Derate above 25°C
Total Power Dissipation @ TA = 25°C, when mounted with the minimum recommended pad size
PD
125
Watts
1.0
W/°C
2.5
Watts
Operating and Storage Temperature Range
TJ, Tstg – 55 to 150 °C
Single Pulse Drain–to–Source Avalanche Energy — Starting TJ = 25°C
(VDD = 25 Vdc, VGS = 10 Vpk, IL = 23 Apk, L = 5.7 mH, RG = 25 Ω)
EAS
1500
mJ
Thermal Resistance — Junction to Case
Thermal Resistance — Junction to Ambient
Thermal Resistance — Junction to Ambient, when mounted with the minimum recommended pad size
R_θJC
R_θJA
R_θJA
1.0
°C/W
62.5
50
Maximum Lead Temperature for Soldering Purposes, 1/8″ from case for 10 seconds
TL
260
°C
Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit
curves — representing boundaries on device characteristics — are given to facilitate “worst case” design.
E–FET and Designer’s are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc.
Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
©^MM^oot^to^oro^rola^l,^aIn^Tc.^M19^O9^S4 ^{Power MOSFET Transistor Device Data}
1