A3PN015-QNG68 Datasheet, PDF (45/114 Pages) Microsemi Corporation – ProASIC3 nano Flash FPGAs

ProASIC3 nano Flash FPGAs
Timing Characteristics
Table 2-40 • 2.5 V LVCMOS Low Slew
Commercial-Case Conditions: T_J = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V
Software Default Load at 35 pF for A3PN060, A3PN125, A3PN250
Drive
Strength
2 mA
Speed
Grade
Std.
t_DOUT
0.60
t_DP
11.29
t_DIN
0.04
t_PY
1.43
t_PYS
1.63
t_EOUT
0.43
t_ZL
t_ZH
10.64 11.29
t_LZ
2.27
t_HZ Units
2.29 ns
–1
0.51 9.61 0.04 1.22 1.39 0.36 9.05 9.61 1.93 1.95 ns
–2
0.45 8.43 0.03 1.07 1.22 0.32 7.94 8.43 1.70 1.71 ns
4 mA
Std.
0.60 11.29 0.04 1.43 1.63 0.43 10.64 11.29 2.27 2.29 ns
–1
0.51 9.61 0.04 1.22 1.39 0.36 9.05 9.61 1.93 1.95 ns
–2
0.45 8.43 0.03 1.07 1.22 0.32 7.94 8.43 1.70 1.71 ns
6 mA
Std.
0.60 7.73 0.04 1.43 1.63 0.43 7.70 7.73 2.60 2.89 ns
–1
0.51 6.57 0.04 1.22 1.39 0.36 6.55 6.57 2.21 2.46 ns
–2
0.45 5.77 0.03 1.07 1.22 0.32 5.75 5.77 1.94 2.16 ns
8 mA
Std.
0.60 7.73 0.04 1.43 1.63 0.43 7.70 7.73 2.60 2.89 ns
–1
0.51 6.57 0.04 1.22 1.39 0.36 6.55 6.57 2.21 2.46 ns
–2
0.45 5.77 0.03 1.07 1.22 0.32 5.75 5.77 1.94 2.16 ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-5 for derating values.
Table 2-41 • 2.5 V LVCMOS High Slew
Commercial-Case Conditions: T_J = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V
Software Default Load at 35 pF for A3PN060, A3PN125, A3PN250
Drive
Strength
2 mA
Speed
Grade
Std.
t_DOUT
0.60
t_DP
8.38
t_DIN
0.04
t_PY
1.43
t_PYS
1.63
t_EOUT
0.43
t_ZL
7.36
t_ZH
8.38
t_LZ
2.27
t_HZ Units
2.37 ns
–1
0.51 7.13 0.04 1.22 1.39 0.36 6.26 7.13 1.93 2.02 ns
–2
0.45 6.26 0.03 1.07 1.22 0.32 5.50 6.26 1.69 1.77 ns
4 mA
Std.
0.60 8.38 0.04 1.43 1.63 0.43 7.36 8.38 2.27 2.37 ns
–1
0.51 7.13 0.04 1.22 1.39 0.36 6.26 7.13 1.93 2.02 ns
–2
0.45 6.26 0.03 1.07 1.22 0.32 5.50 6.26 1.69 1.77 ns
6 mA
Std.
0.60 4.94 0.04 1.43 1.63 0.43 4.71 4.94 2.60 2.98 ns
–1
0.51 4.20 0.04 1.22 1.39 0.36 4.01 4.20 2.21 2.54 ns
–2
0.45 3.69 0.03 1.07 1.22 0.32 3.52 3.69 1.94 2.23 ns
8 mA
Std.
0.60 4.94 0.04 1.43 1.63 0.43 4.71 4.94 2.60 2.98 ns
–1
0.51 4.20 0.04 1.22 1.39 0.36 4.01 4.20 2.21 2.54 ns
–2
0.45 3.69 0.03 1.07 1.22 0.32 3.52 3.69 1.94 2.23 ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-5 for derating values.
Revision 11
2- 31