DSPIC33FJ06GS001_12 Datasheet, PDF (1/352 Pages) Microchip Technology – 16-Bit Microcontrollers and Digital Signal Controllers with High-Speed PWM, ADC and Comparators

dsPIC33FJ06GS001/101A/102A/202A
and dsPIC33FJ09GS302
16-Bit Microcontrollers and Digital Signal Controllers with
High-Speed PWM, ADC and Comparators
Operating Conditions
• 3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
Core: 16-Bit dsPIC33F CPU
• Code Efficient (C and Assembly) Architecture
• Two 40-Bit Wide Accumulators
• Single-Cycle (MAC/MPY) with Dual Data Fetch
• Single-Cycle Mixed-Sign MUL plus Hardware Divide
• 32-Bit Multiply Support
Clock Management
• ±2% Internal Oscillator
• Programmable PLLs and Oscillator Clock Sources
• Fail-Safe Clock Monitor (FSCM)
• Independent Watchdog Timer (WDT)
• Fast Wake-up and Start-up
Power Management
• Low-Power Management modes (Sleep, Idle, Doze)
• Integrated Power-on Reset and Brown-out Reset
• 2.0 mA/MHz Dynamic Current (typical)
• 135 µA IPD Current (typical)
High-Speed PWM
• Up to Three PWM Pairs with Independent Timing
• Dead Time for Rising and Falling Edges
• 1.04 ns PWM Resolution for Dead Time, Duty Cycle,
Phase and Frequency
• PWM Support for:
- DC/DC, AC/DC, Inverters, PFC and Lighting
• Programmable Fault Inputs
• Flexible Trigger Configurations for ADC Conversions
Advanced Analog Features
• Two High-Speed Comparators with Direct Connection to
the PWM module:
- Buffered/amplified output drive
- Independent 10-bit DAC for each comparator
- Rail-to-rail comparator operation
- DACOUT amplifier (1x, 1.8x)
- Selectable hysteresis
- Programmable output polarity
- Interrupt generation capability
Advanced Analog Features (Continued)
• ADC module:
- 10-bit resolution with Successive Approximation
Register (SAR) converter (2 Msps) and three
Sample-and-Hold (S&H) circuits
- Up to 8 input channels grouped into four conversion
pairs, plus two inputs for monitoring voltage references
- Flexible and independent ADC trigger sources
- Dedicated Result register for each
analog channel
Timers/Output Compare/Input Capture
• Two 16-Bit General Purpose Timers/Counters
• Input Capture module
• Output Compare module
• Peripheral Pin Select (PPS) to allow Function Remap
Communication Interfaces
• UART module (10 Mbps):
- With support for LIN/J2602 protocols and IrDA^®
• 4-Wire SPI module
• I²C™ module (up to 1 Mbaud) with SMBus Support
• PPS to allow Function Remap
Input/Output
• Constant Current Source:
- Constant current generator (10 µA nominal)
• Sink/Source 18 mA on 8 Pins and 6 mA on 13 Pins
• 5V Tolerant Pins
• Selectable Open-Drain and Pull-ups
• External Interrupts on 16 I/O Pins
Qualification and Class B Support
• AEC-Q100 REVG (Grade 1, -40ºC to +125ºC) Planned
• Class B Safety Library, IEC 60730
Debugger Development Support
• In-Circuit and In-Application Programming
• Two Breakpoints
• IEEE 1149.2 Compatible (JTAG) Boundary Scan
• Trace and Run-Time Watch
 2011-2012 Microchip Technology Inc.
DS75018C-page 1