|
DSPIC33EPXXX806 Datasheet, PDF (1/614 Pages) Microchip Technology – 16-bit Microcontrollers and Digital Signal Controllers (up to 512 KB Flash and 52 KB SRAM) with High-Speed PWM, USB, and Advanced Analog | |||
|
dsPIC33EPXXX(GP/MC/MU)806/810/814
and PIC24EPXXX(GP/GU)810/814
16-bit Microcontrollers and Digital Signal Controllers (up to 512 KB Flash
and 52 KB SRAM) with High-Speed PWM, USB, and Advanced Analog
Operating Conditions
⢠3.0V to 3.6V, -40ºC to +125ºC, DC to 60 MIPS
⢠3.0V to 3.6V, -40ºC to +85ºC, DC to 70 MIPS
Core: 16-bit dsPIC33E/PIC24E CPU
⢠Code-efficient (C and Assembly) architecture
⢠Two 40-bit wide accumulators
⢠Single-cycle (MAC/MPY) with dual data fetch
⢠Single-cycle mixed-sign MUL plus hardware divide
⢠32-bit multiply support
Clock Management
⢠2% internal oscillator
⢠Programmable PLLs and oscillator clock sources
⢠Fail-Safe Clock Monitor (FSCM)
⢠Independent Watchdog Timer
⢠Fast wake-up and start-up
Power Management
⢠Low-power management modes (Sleep, Idle, Doze)
⢠Integrated Power-on Reset and Brown-out Reset
⢠1.0 mA/MHz dynamic current (typical)
⢠60 µA IPD current (typical)
High-Speed PWM
⢠Up to seven PWM pairs with independent timing
⢠Dead Time for rising and falling edges
⢠8.32 ns PWM resolution
⢠PWM support for:
- DC/DC, AC/DC, Inverters, PFC, Lighting
- BLDC, PMSM, ACIM, SRM
⢠Programmable Fault inputs
⢠Flexible trigger configurations for ADC conversions
Advanced Analog Features
⢠Two independent ADC modules:
- One ADC configurable as 10-bit, 1.1 Msps with four
S&H or 12-bit, 500 ksps with one S&H
- One 10-bit ADC, 1.1 Msps with four S&H
- Eight S&H using both ADC 10-bit modules
- 24 analog channels (64-pin devices) up to 32 analog
channels (100/121/144-pin devices)
⢠Flexible and independent ADC trigger sources
⢠Comparators:
- Up to three Analog Comparator modules
- Programmable references with 32 voltage points
Timers/Output Compare/Input Capture
⢠27 General Purpose Timers:
- Nine 16-bit and up to four 32-bit Timers/Counters
- 16 OC modules configurable as Timers/Counters
- Two 32-bit Quadrature Encoder Interface (QEI)
modules configurable as Timers/Counters
⢠16 IC modules
⢠Peripheral Pin Select (PPS) to allow function remap
⢠Real-Time Clock and Calendar (RTCC) module
Communication Interfaces
⢠USB 2.0 OTG-compliant full-speed interface
⢠Four UART modules (15 Mbps)
- Supports LIN 2.0 protocols and IrDA®
⢠Four 4-wire SPI modules (15 Mbps)
⢠Two ECAN⢠modules (1 Mbaud) CAN 2.0B support
⢠Two I2C modules (up to 1 Mbaud) with SMBus support
⢠Data Converter Interface (DCI) module with support for
I2S and Audio codecs
⢠PPS to allow function remap
⢠Parallel Master Port (PMP)
⢠Programmable Cyclic Redundancy Check (CRC)
Direct Memory Access (DMA)
⢠15-channel DMA with user-selectable priority arbitration
⢠UART, USB, SPI, ADC, ECAN, IC, OC, Timers,
DCI/I2S, PMP
Input/Output
⢠Sink/Source 10 mA on all pins
⢠5V-tolerant pins
⢠Selectable open drain, pull-ups, and pull-downs
⢠Up to 5 mA overvoltage clamp current
⢠External interrupts on all I/O pins
Qualification and Class B Support
⢠AEC-Q100 REVG (Grade 1 -40ºC to +125ºC) planned
⢠AEC-Q100 REVG (Grade 0 -40ºC to +150ºC) planned
⢠Class B Safety Library, IEC 60730
Debugger Development Support
⢠In-circuit and in-application programming
⢠Five program and three complex data breakpoints
⢠IEEE 1149.2-compatible (JTAG) boundary scan
⢠Trace and run-time watch
Packages
Type
QFN
TQFP
Pin Count
64
64
144
I/O Pins (up to)
53
53
122
Contact/Lead Pitch
0.50
0.50
0.40
Dimensions
9x9x0.9
10x10x1 16x16x1
Note: All dimensions are in millimeters (mm) unless specified.
TQFP
100
83
0.40
0.50
12x12x1 14x14x1
TFBGA
121
83
0.50
10x10x1.2
LQFP
144
122
0.50
20x20x1.4
© 2009-2012 Microchip Technology Inc.
Preliminary
DS70616F-page 1
|
▷ |