MAX15026_12 Datasheet, PDF (3/23 Pages) Maxim Integrated Products – Low-Cost, Small, 4.5V to 28V Wide Operating Range, DC-DC Synchronous Buck Controller

Low-Cost, Small, 4.5V to 28V Wide Operating
Range, DC-DC Synchronous Buck Controller
ELECTRICAL CHARACTERISTICS (continued)
(V_IN = 12V, R_RT = 27kΩ, R_LIM = 30kΩ, C_VCC = 4.7µF, C_IN = 1µF, T_A = -40°C to +85°C (MAX15026B/CETD+, MAX15026BETD/V+),
T_A = T_J = -40°C to +125°C (MAX15026B/C/DATD+), unless otherwise noted. Typical values are at T_A = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
ENABLE (EN)
EN Input High
EN Input Low
EN Input Leakage Current
OSCILLATOR
Switching Frequency
1MHz Switching Frequency
2MHz Switching Frequency
V_{EN_H}
V_{EN_L}
I_{LEAK_EN}
V_EN rising
V_EN falling
V_EN = 5.5V
f_SW
R_RT = 27kΩ
R_RT = 15.7kΩ
R_RT = 7.2kΩ
1.14
0.997
-1
1.20
1.05
1.26
1.103
+1
540 600 660
0.9
1
1.1
1.8
2.0
2.4
V
V
µA
kHz
MHz
MHz
Switching Frequency Adjustment
Range (Note 3)
200
2000
kHz
RT Voltage
PWM Ramp Peak-to-Peak
Amplitude
V_RT
V_RAMP
1.19 1.205 1.22
V
1.8
V
PWM Ramp Valley
Minimum Controllable On-Time
V_VALLEY
0.8
V
65
100
ns
Maximum Duty Cycle
Minimum Low-Side On-Time
OUTPUT DRIVERS/DRIVER SUPPLY (DRV)
f_SW = 600kHz
R_RT = 15.7kΩ
85
88
%
75
110 150
ns
DRV Undervoltage Lockout
V_{DRV_UVLO} V_DRV rising
4.0
4.2
4.4
V
DRV Undervoltage Lockout
Hysteresis
400
mV
DH On-Resistance
DL On-Resistance
DH Peak Current
Low, sinking 100mA, V_BST = 5V
High, sourcing 100mA, V_BST = 5V
Low, sinking 100mA, V_BST = 5.2V
High, sourcing 100mA, V_BST = 5.2V
C_LOAD = 10nF
Sinking
Sourcing
1
3
Ω
1.5
4.5
1
3
Ω
1.5
4.5
4
A
3
DL Peak Current
C_LOAD = 10nF
Sinking
Sourcing
4
A
3
DH/DL Break-Before-Make Time
DH at 1V (falling) to DL at 1V (rising)
10 (18, Note 5)
ns
DL/DH Break-Before-Make Time
DL at 1V (falling) to DH at 1V (rising)
10 (20, Note 6)
ns
SOFT-START
Soft-Start Duration
2048
Switching
Cycles
Reference Voltage Steps
64
Steps
CURRENT LIMIT/HICCUP
Current-Limit Threshold
Adjustment Range
Cycle-by-cycle valley current-limit
threshold adjustment range
30
valley limit = V_LIM/10
300
mV
_______________________________________________________________________________________ 3