English
Language : 

MAX1471_05 Datasheet, PDF (26/26 Pages) Maxim Integrated Products – 315MHz/434MHz Low-Power, 3V/5V ASK/FSK Superheterodyne Receiver
◁
315MHz/434MHz Low-Power, 3V/5V
ASK/FSK Superheterodyne Receiver
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
COMMON DIMENSIONS
PKG.
16L 5x5
20L 5x5
28L 5x5
32L 5x5
40L 5x5
SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX.
A 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80
A1
0 0.02 0.05 0 0.02 0.05 0 0.02 0.05 0 0.02 0.05 0 0.02 0.05
A3
0.20 REF.
0.20 REF.
0.20 REF.
0.20 REF.
0.20 REF.
b
0.25 0.30 0.35 0.25 0.30 0.35 0.20 0.25 0.30 0.20 0.25 0.30 0.15 0.20 0.25
D
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
E
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
e
0.80 BSC.
0.65 BSC.
0.50 BSC.
0.50 BSC.
0.40 BSC.
k
0.25 - - 0.25 - - 0.25 - - 0.25 - - 0.25 0.35 0.45
L
0.30 0.40 0.50 0.45 0.55 0.65 0.45 0.55 0.65 0.30 0.40 0.50 0.40 0.50 0.60
L1
- - - - - - - - - - - - 0.30 0.40 0.50
N
16
20
28
32
40
ND
4
5
7
8
10
NE
4
5
7
8
10
JEDEC
WHHB
WHHC
WHHD-1
WHHD-2
-----
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL
CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE
OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1
IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN
0.25 mm AND 0.30 mm FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT EXPOSED PAD DIMENSION FOR T2855-1,
T2855-3, AND T2855-6.
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
11. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
12. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
13. LEAD CENTERLINES TO BE AT TRUE POSITION AS DEFINED BY BASIC DIMENSION "e", ±0.05.
-DRAWING NOT TO SCALE-
PKG.
CODES
T1655-1
T1655-2
T1655N-1
T2055-2
T2055-3
T2055-4
T2055-5
T2855-1
T2855-2
T2855-3
T2855-4
T2855-5
T2855-6
T2855-7
T2855-8
T2855N-1
T3255-2
T3255-3
T3255-4
T3255N-1
T4055-1
EXPOSED PAD VARIATIONS
D2
E2
L
MIN. NOM. MAX. MIN. NOM. MAX. ±0.15
DOWN
BONDS
ALLOWED
3.00 3.10 3.20 3.00 3.10 3.20 **
3.00 3.10 3.20 3.00 3.10 3.20 **
3.00 3.10 3.20 3.00 3.10 3.20 **
NO
YES
NO
3.00 3.10 3.20 3.00 3.10 3.20 **
NO
3.00 3.10 3.20 3.00 3.10 3.20 **
YES
3.00 3.10 3.20 3.00 3.10 3.20 **
3.15 3.25 3.35 3.15 3.25 3.35 0.40
NO
YES
3.15 3.25 3.35 3.15 3.25 3.35 **
2.60 2.70 2.80 2.60 2.70 2.80 **
3.15 3.25 3.35 3.15 3.25 3.35 **
2.60 2.70 2.80 2.60 2.70 2.80 **
NO
NO
YES
YES
2.60 2.70 2.80 2.60 2.70 2.80 **
3.15 3.25 3.35 3.15 3.25 3.35 **
2.60 2.70 2.80 2.60 2.70 2.80 **
3.15 3.25 3.35 3.15 3.25 3.35 0.40
3.15 3.25 3.35 3.15 3.25 3.35 **
3.00 3.10 3.20 3.00 3.10 3.20 **
3.00 3.10 3.20 3.00 3.10 3.20 **
3.00 3.10 3.20 3.00 3.10 3.20 **
3.00 3.10 3.20 3.00 3.10 3.20 **
NO
NO
YES
YES
NO
NO
YES
NO
NO
3.20 3.30 3.40 3.20 3.30 3.40 **
YES
** SEE COMMON DIMENSIONS TABLE
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
21-0140
H
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
26 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.