MAX1032_11 Datasheet, PDF (25/32 Pages) Maxim Integrated Products – 8- and 4-Channel, ±3 x VREF Multirange Inputs, Serial 14-Bit ADCs

8- and 4-Channel, ±3 x V_REF
Multirange Inputs, Serial 14-Bit ADCs
This prevents the MAX1032/MAX1033 from inadvertent-
ly exiting full power-down mode because of a CS glitch
in a noisy digital environment.
Power-On Reset
The MAX1032/MAX1033 power up in normal operation
configured for external clock mode with all circuitry
active (Tables 7 and 8). Each analog input channel
(CH0–CH7) is set for single-ended conversions with a
±3 x V_REF bipolar input range (Table 6).
Allow the power supplies to stabilize after power-up. Do
not initiate any conversions until the power supplies
have stabilized. Additionally, allow 10ms for the internal
reference to stabilize when C_REF = 1.0µF and C_REFCAP
= 0.1µF. Larger reference capacitors require longer
stabilization times.
Internal or External Reference
The MAX1032/MAX1033 operate with either an internal or
external reference. The reference voltage impacts the
ADC’s FSR (Figures 12, 13, and 14). An external refer-
ence is recommended if more accuracy is required than
the internal reference provides, and/or multiple converters
require the same reference voltage.
Internal Reference
The MAX1032/MAX1033 contain an internal 4.096V
bandgap reference. This bandgap reference is connect-
ed to REFCAP through a nominal 5kΩ resistor (Figure 17).
The voltage at REFCAP is buffered creating 4.096V at
REF. When using the internal reference, bypass
REFCAP with a 0.1µF or greater capacitor to AGND1 and
bypass REF with a 1.0µF or greater capacitor to AGND1.
SAR
ADC ^REF
4.096V
MAX1032
MAX1033
1x
5kΩ
4.096V
BANDGAP
REFERENCE
REF
1.0µF
REFCAP
V_RCTH
AGND1
0.1µF
Figure 17. Internal Reference Operation
External Reference
For external reference operation, disable the internal
reference and reference buffer by connecting REFCAP
to AVDD1. With AVDD1 connected to REFCAP, REF
becomes a high-impedance input and accepts an
external reference voltage. The MAX1032/
MAX1033 can accept an external reference voltage of
4.096V or less. However, to meet all of the Electrical
Characteristics specifications, V_REF must be > 3.8V.
The MAX1032/MAX1033 external reference current
varies depending on the applied reference voltage and
the operating mode (see the External Reference Input
Current vs. External Reference Input Voltage in the
Typical Operating Characteristics).
Applications Information
Noise Reduction
Additional samples can be taken and averaged (over-
sampling) to remove the effect of transition noise on
conversion results. The square root of the number of
samples determines the improvement in performance.
For example, with 2/3LSB_RMS (4LSB_P-P) transition
noise, 16 (4² = 16) samples must be taken to reduce
the noise to 1LSB_P-P.
Interface with 0 to 10V Signals
In industrial-control applications, 0 to 10V signaling is
common. For 0 to 10V applications, configure the
selected MAX1032/MAX1033 input channel for the sin-
gle-ended 0 to ±3 x V_REF input range (R[2:0] = 110,
Table 6). The 0 to ±3 x V_REF range accommodates 0 to
10V where the signals saturate at approximately ±3 x
V_REF if out of range.
Interface with 4–20mA Signals
Figure 19 illustrates a simple interface between the
MAX1032/MAX1033 and a 4–20mA signal. 4–20mA sig-
naling can be used as a binary switch (4mA represents
a logic-low signal, 20mA represents a logic-high sig-
nal), or for precision communication where currents
between 4mA and 20mA represent intermediate analog
data. For binary switch applications, connect the
4–20mA signal to the MAX1032/MAX1033 with a resis-
tor to ground. For example, a 250Ω resistor converts
the 4–20mA signal to a 1V to 5V signal. Adjust the
resistor value so the parallel combination of the resistor
and the MAX1032/MAX1033 source impedance is
250Ω. In this application, select the single-ended 0 to 3
x V_REF/2 range (R[2:0] = 011, Table 6). For applications
that require precision measurements of continuous
analog currents between 4mA and 20mA, use a buffer
to prevent the MAX1032/MAX1033 input from diverting
current from the 4–20mA signal.
______________________________________________________________________________________ 25