LTC3727-1_15 Datasheet, PDF (21/32 Pages) Linear Technology – High Efficiency, 2-Phase Synchronous Step-Down Switching Regulators

LTC3727/LTC3727-1
APPLICATIO S I FOR ATIO
The phase detector used is an edge sensitive digital type
which provides zero degrees phase shift between the
external and internal oscillators. This type of phase detec-
tor will not lock up on input frequencies close to the
harmonics of the VCO center frequency. The PLL hold-in
range, Δf_H, is equal to the capture range, Δf_C:
Δf_H = Δf_C = ±0.5 f_O (250kHz-550kHz)
The output of the phase detector is a complementary pair
of current sources charging or discharging the external
filter network on the PLLFLTR pin.
If the external frequency (f_PLLIN) is greater than the oscil-
lator frequency f_0SC, current is sourced continuously,
pulling up the PLLFLTR pin. When the external frequency
is less than f_0SC, current is sunk continuously, pulling
down the PLLFLTR pin. If the external and internal fre-
quencies are the same but exhibit a phase difference, the
current sources turn on for an amount of time correspond-
ing to the phase difference. Thus the voltage on the
PLLFLTR pin is adjusted until the phase and frequency of
the external and internal oscillators are identical. At this
stable operating point the phase comparator output is
open and the filter capacitor C_LP holds the voltage. The
LTC3727 PLLIN pin must be driven from a low impedance
source such as a logic gate located close to the pin. When
using multiple LTC3727s for a phase-locked system, the
PLLFLTR pin of the master oscillator should be biased at
a voltage that will guarantee the slave oscillator(s) ability
to lock onto the master’s frequency. A DC voltage of 0.7V
to 1.7V applied to the master oscillator’s PLLFLTR pin is
recommended in order to meet this requirement. The
resultant operating frequency can range from 310kHz to
470kHz.
The loop filter components (C_LP, R_LP) smooth out the
current pulses from the phase detector and provide a
stable input to the voltage controlled oscillator. The filter
components C_LP and R_LP determine how fast the loop
acquires lock. Typically R_LP =10kΩ and C_LP is 0.01μF to
0.1μF.
Minimum On-Time Considerations
Minimum on-time t_ON(MIN) is the smallest time duration
that the LTC3727 is capable of turning on the top MOSFET.
It is determined by internal timing delays and the gate
charge required to turn on the top MOSFET. Low duty cycle
applications may approach this minimum on-time limit
and care should be taken to ensure that
t_ON(MIN)
<
V_OUT
V_IN(f)
If the duty cycle falls below what can be accommodated by
the minimum on-time, the LTC3727 will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple voltage and current will increase.
The minimum on-time for the LTC3727 is generally less
than 200ns. However, as the peak sense voltage decreases
the minimum on-time gradually increases up to about
300ns. This is of particular concern in forced continuous
applications with low ripple current at light loads. If the
duty cycle drops below the minimum on-time limit in this
situation, a significant amount of cycle skipping can occur
with correspondingly larger inductor current and output
voltage ripple.
FCB Pin Operation
The FCB pin can be used to regulate a secondary winding
or as a logic level input. Continuous operation is forced on
both controllers when the FCB pin drops below 0.8V.
During continuous mode, current flows continuously in
the transformer primary. The secondary winding(s) draw
current only when the bottom, synchronous switch is on.
When primary load currents are low and/or the V_IN/V_OUT
ratio is low, the synchronous switch may not be on for a
sufficient amount of time to transfer power from the
output capacitor to the secondary load. Forced continuous
operation will support secondary windings providing there
is sufficient synchronous switch duty factor. Thus, the
FCB input pin removes the requirement that power must
3727fc
21