LTC3727-1_15 Datasheet, PDF (10/32 Pages) Linear Technology – High Efficiency, 2-Phase Synchronous Step-Down Switching Regulators

LTC3727/LTC3727-1
U
OPERATIO (Refer to Functional Diagram)
The top MOSFET drivers are biased from floating boot-
strap capacitor C_B, which normally is recharged during
each off cycle through an external diode when the top
MOSFET turns off. As V_IN decreases to a voltage close to
V_OUT, the loop may enter dropout and attempt to turn on
the top MOSFET continuously. The dropout detector de-
tects this and forces the top MOSFET off for about 400ns
every tenth cycle to allow C_B to recharge.
The main control loop is shut down by pulling the RUN/SS
pin low. Releasing RUN/SS allows an internal 1.2μA
current source to charge soft-start capacitor C_SS. When
C_SS reaches 1.5V, the main control loop is enabled with the
I_TH voltage clamped at approximately 30% of its maximum
value. As C_SS continues to charge, the I_TH pin voltage is
gradually released allowing normal, full-current opera-
tion. When both RUN/SS1 and RUN/SS2 are low, all
LTC3727/LTC3727-1 controller functions are shut down,
including the 7.5V and 3.3V regulators.
Low Current Operation
The FCB pin is a multifunction pin providing two func-
tions: 1) to provide regulation for a secondary winding by
temporarily forcing continuous PWM operation on
both controllers; and 2) to select between two modes of
low current operation. When the FCB pin voltage is below
0.8V, the controller forces continuous PWM current
mode operation. In this mode, the top and bottom
MOSFETs are alternately turned on to maintain the output
voltage independent of direction of inductor current.
When the FCB pin is below V_INTVCC – 2V but greater than
0.8V, the controller enters Burst Mode operation. Burst
Mode operation sets a minimum output current level
before inhibiting the top switch and turns off the synchro-
nous MOSFET(s) when the inductor current goes nega-
tive. This combination of requirements will, at low cur-
rents, force the I_TH pin below a voltage threshold that will
temporarily inhibit turn-on of both output MOSFETs until
the output voltage drops. There is 60mV of hysteresis in
the burst comparator B tied to the I_TH pin. This hysteresis
produces output signals to the MOSFETs that turn them
on for several cycles, followed by a variable “sleep”
interval depending upon the load current. The resultant
output voltage ripple is held to a very small value by
10
having the hysteretic comparator follow the error ampli-
fier gain block.
Frequency Synchronization
The phase-locked loop allows the internal oscillator to be
synchronized to an external source via the PLLIN pin. The
output of the phase detector at the PLLFLTR pin is also the
DC frequency control input of the oscillator that operates
over a 250kHz to 550kHz range corresponding to a DC
voltage input from 0V to 2.4V. When locked, the PLL
aligns the turn on of the top MOSFET to the rising edge of
the synchronizing signal. When PLLIN is left open, the
PLLFLTR pin goes low, forcing the oscillator to its mini-
mum frequency.
Continuous Current (PWM) Operation
Tying the FCB pin to ground will force continuous current
operation. This is the least efficient operating mode, but
may be desirable in certain applications. The output can
source or sink current in this mode. When sinking current
while in forced continuous operation, current will be
forced back into the main power supply potentially boost-
ing the input supply to dangerous voltage levels—
BEWARE!
INTV_CC/EXTV_CC Power
Power for the top and bottom MOSFET drivers and most
other internal circuitry is derived from the INTV_CC pin.
When the EXTV_CC pin is left open, an internal 7.5V low
dropout linear regulator supplies INTV_CC power. If EXTV_CC
is taken above 7.3V, the 7.5V regulator is turned off and an
internal switch is turned on connecting EXTV_CC to INTV_CC.
This allows the INTV_CC power to be derived from a high
efficiency external source such as the output of the regu-
lator itself or a secondary winding, as described in the
Applications Information section.
Output Overvoltage Protection
An overvoltage comparator, OV, guards against transient
overshoots (>7.5%) as well as other more serious condi-
tions that may overvoltage the output. In this case, the top
MOSFET is turned off and the bottom MOSFET is turned on
until the overvoltage condition is cleared.
3727fc