LTC3770_15 Datasheet, PDF (19/24 Pages) Linear Technology – Fast No RSENSE Step-Down Synchronous Controller with Margining, Tracking and PLL

LTC3770
APPLICATIONS INFORMATION
oscillators are identical. At this stable operating point the
phase comparator output is open and the filter capacitor
C_LP holds the voltage. The LTC3770 PLLIN pin must be
driven from a low impedance source such as a logic gate
located close to the pin.
The loop filter components (C_LP, R_LP) smooth out the
current pulses from the phase detector and provide a
stable input to the voltage controlled oscillator. The filter
components C_LP and R_LP determine how fast the loop
acquires lock. Typically R_LP =10kΩ and C_LP is 0.01μF to
0.1μF.
Dead Time Control
To further optimize the efficiency, the LTC3770 gives us-
ers some control over the dead time of the Top gate low
and Bottom gate high transition. By applying a DC voltage
on the Z0 pin, the TG low BG high dead time can be pro-
grammed. Because the dead time is a strong function of
the load current and the type of MOSFET used, users need
to be careful to optimize the dead time for their particular
applications. Figure 11 shows the relation between the TG
Low BG High Dead time by varying the Z0 voltages. For
an application using LTC3770 with load current of 5A and
IR7811W MOSFETs, the dead time could be optimized. To
make sure that there is no shoot-through under all condi-
tions, a dead time of 70ns is selected. This corresponds to
a DC voltage about 2.6V on Z0 pin. This voltage can easily
be generated with a resistor divider off INTV_CC.
180
160
140
120
100
80
60
40
20
0 I_OUT = 5A
IR7811W FETs
–20
0
1
2
3
Z0 VOLTAGE (V)
4
5
3770 F11
Figure 11. TG Low BG High Dead Time vs Z0 Voltage
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Although all dissipative
elements in the circuit produce losses, four main sources
account for most of the losses in LTC3770 circuits:
1. DC I²R losses. These arise from the resistances of the
MOSFETs, inductor and PC board traces and cause the
efficiency to drop at high output currents. In continuous
mode the average output current flows through L, but is
chopped between the top and bottom MOSFETs. If the two
MOSFETs have approximately the same R_DS(ON), then the
resistance of one MOSFET can simply be summed with
the resistances of L and the board traces to obtain the
DC I²R loss. For example, if R_DS(ON) = 0.01Ω and R_L =
0.005Ω, the loss will range from 15mW to 1.5W as the
output current varies from 1A to 10A.
2. Transition loss. This loss arises from the brief amount
of time the top MOSFET spends in the saturated region
during switch node transitions. It depends upon the
input voltage, load current, driver strength and MOSFET
capacitance, among other factors. The loss is significant
at input voltages above 20V and can be estimated from:
Transition Loss ≅ (1.7A^–1) V_IN2 I_OUT C_RSS f
3. INTV_CC current. This is the sum of the MOSFET driver
and control currents.
4. C_IN loss. The input capacitor has the difficult job of
filtering the large RMS input current to the regulator. It
must have a very low ESR to minimize the AC I²R loss and
sufficient capacitance to prevent the RMS current from
causing additional upstream losses in fuses or batteries.
Other losses, including C_OUT ESR loss, Schottky diode D1
conduction loss during dead time and inductor core loss
generally account for less than 2% additional loss.
When making adjustments to improve efficiency, the
input current is the best indicator of changes in efficiency.
3770fc
19