English
Language : 

LTC3865-1_15 Datasheet, PDF (14/38 Pages) Linear Technology – Dual, 2-Phase Synchronous DC/DC Controller with Pin Selectable Outputs
LTC3865/LTC3865-1
OPERATION
bad mask is 100μs when there are any VID transitions.
On the LTC3865-1 (UH32 package) or the LTC3865 (FE38
package), each channel has its own PGOOD pin. Therefore,
the PGOOD pins now only respond to their own channels.
The PGOOD pins are allowed to be pulled up by external
resistors to sources of up to 6V.
Output Overvoltage Protection
An overvoltage comparator, OV, guards against transient
overshoots (>10%) as well as other more serious condi-
tions that may overvoltage the output. In such cases,
the top MOSFET is turned off and the bottom MOSFET is
turned on until the reverse current limit for the overvoltage
condition is reached. The bottom MOSFET will be turned on
again at the next clock and be turned off when the reverse
current limit is reached again. This process repeats until
the overvoltage condition is cleared.
Output Voltage Programming
The output voltages of both channels of the LTC3865/
LTC3865-1 can be programmed to a preset value. There
are two VID pins for each channel and by connecting these
pins to INTVCC, GND, or by floating them, the output volt-
ages can be set to the values in Table 1.
Table 1. Programming of Output Voltage
VID11/VID21
VID12/VID22
INTVCC
INTVCC
INTVCC
Float
Float
INTVCC
Float
GND
INTVCC
Float
Float
GND
GND
INTVCC
GND
Float
GND
GND
VOUT1/VOUT2 (V)
5.0
3.3
2.5
1.8
0.6 or External Divider
1.5
1.2
1.0
1.1
APPLICATIONS INFORMATION
The Typical Application on the first page is a basic LTC3865
application circuit. The LTC3865 can be configured to use
either DCR (inductor resistance) sensing or low value resis-
tor sensing. The choice between the two current sensing
schemes is largely a design trade-off between cost, power
consumption and accuracy. DCR sensing is becoming
popular because it saves expensive current sensing resis-
tors and is more power efficient, especially in high current
applications. However, current sensing resistors provide
the most accurate current limits for the controller. Other
external component selection is driven by the load require-
ment, and begins with the selection of RSENSE (if RSENSE is
used) and inductor value. Next, the power MOSFETs are se-
lected. Finally, input and output capacitors are selected.
Current Limit Programming
The ILIM pin is a tri-level logic input which sets the maxi-
mum current limit of the controller. When ILIM is either
grounded, floated or tied to INTVCC, the typical value for
the maximum current sense threshold will be 30mV, 50mV
or 75mV, respectively.
Which setting should be used? For the best current limit
accuracy, use the 75mV setting. The 30mV setting will
allow for the use of very low DCR inductors or sense
resistors, but at the expense of current limit accuracy.
The 50mV setting is a good balance between the two. For
single output dual phase applications, use the 50mV or
75mV setting for optimal current sharing.
SENSE+ and SENSE– Pins
The SENSE+ and SENSE– pins are the inputs to the current
comparators. The common mode input voltage range of
the current comparators is 0V to 5V. Both SENSE pins
are high impedance inputs with small base currents of
less than 1μA. When the SENSE pins ramp up from 0V to
1.4V, the small base currents flow out of the SENSE pins.
When the SENSE pins ramp down from 5V to 1.1V, the
small base currents flow into the SENSE pins. The high
impedance inputs to the current comparators allow ac-
curate DCR sensing. However, care must be taken not to
float these pins during normal operation.
3865fb
14