GAL16V8 Datasheet, PDF (10/22 Pages) Lattice Semiconductor – High Performance E2CMOS PLD Generic Array Logic

Specifications GAL16V8D
Absolute Maximum Ratings⁽¹⁾
Recommended Operating Conditions
Supply voltage V ...................................... –0.5 to +7V
CC
Input voltage applied .......................... –2.5 to V_CC +1.0V
Off-state output voltage applied ......... –2.5 to V_CC +1.0V
Storage Temperature ................................ –65 to 150°C
Ambient Temperature with
Power Applied ........................................ –55 to 125°C
1.Stresses above those listed under the “Absolute Maximum
Ratings” may cause permanent damage to the device. These
are stress only ratings and functional operation of the device at
these or at any other conditions above those indicated in the
operational sections of this specification is not implied (while
programming, follow the programming specifications).
Commercial Devices:
Ambient Temperature (T_A) ............................... 0 to 75°C
Supply voltage (V_CC)
with Respect to Ground ..................... +4.75 to +5.25V
Industrial Devices:
Ambient
Temperature
(T )
A
...........................
–40
to
85°C
Supply voltage (V_CC)
with Respect to Ground ..................... +4.50 to +5.50V
DC Electrical Characteristics
Over Recommended Operating Conditions (Unless Otherwise Specified)
SYMBOL PARAMETER
CONDITION
MIN. TYP.³ MAX. UNITS
VIL
VIH
IIL¹
IIH
VOL
VOH
IOL
Input Low Voltage
Input High Voltage
Input or I/O Low Leakage Current
Input or I/O High Leakage Current
Output Low Voltage
Output High Voltage
Low Level Output Current
0V ≤ VIN ≤ VIL (MAX.)
3.5V ≤ VIN ≤ VCC
IOL = MAX. Vin = VIL or VIH
IOH = MAX. Vin = VIL or VIH
L-3/-5 & -7 (Ind. PLCC)
Vss – 0.5 —
2.0
—
—
—
—
—
—
—
2.4
—
—
—
L-7 (Except Ind. PLCC)/-10/-15/-25 —
—
Q-10/-15/-20/-25
IOH
IOS²
High Level Output Current
Output Short Circuit Current
VCC = 5V VOUT = 0.5V T_A= 25°C
—
—
–30
—
COMMERCIAL
ICC
Operating Power
Supply Current
VIL = 0.5V VIH = 3.0V
ftoggle = 15MHz Outputs Open
L -3/-5/-7/-10
L-15/-25
Q-10/-15/-25
—
75
—
75
—
45
0.8
V
Vcc+1 V
–100 µA
10
µA
0.5
V
—
V
16
mA
24
mA
–3.2 mA
–150 mA
115 mA
90
mA
55
mA
INDUSTRIAL
ICC
Operating Power
Supply Current
VIL = 0.5V VIH = 3.0V
ftoggle = 15MHz Outputs Open
L -7/-10/-15/-25 —
Q -20/-25
—
75
130
mA
45
65
mA
1) The leakage current is due to the internal pull-up resistor on all pins. See Input Buffer section for more information.
2) One output at a time for a maximum duration of one second. Vout = 0.5V was selected to avoid test problems caused by tester
ground degradation. Characterized but not 100% tested.
3) Typical values are at Vcc = 5V and TA = 25 °C
10