|
CT170-14B-MX23 Datasheet, PDF (8/11 Pages) Japan Aviation Electronics Industry, Ltd. – Crimping Hand Tool | |||
|
◁ |
Japan Aviation Electronics Industry, Ltd.
Connector Div. Production Engineering Dept.
æ¥æ¬èªç©ºé»åå·¥æ¥æ ªå¼ä¼ç¤¾ã³ãã¯ã¿äºæ¥é¨çç£æè¡é¨
Number
çªå·
DCF-S-0126-2A8(0/161.04)
T700344
Page
8ï¼11
5-3.é»ç·ã®ã»ãã
â å³ã®ããã«è¢«è¦ããããé»ç·ãã³ã³ã¿ã¯ãã®ã
ã¬ã«ã®ä¸ã«ã»ãããã¦ãã ããã
被è¦ã®ç«¯é¢ãè¯ç·ãã¬ã«ã¨è¢«è¦ãã¬ã«ã®é
ã«ããããã«ãã¦ãã ããã
â» æ¬ãã³ããã¼ã«ã«é»ç·å
端ãçªãå½ã¦ãã¹ãã
ãã¯ããã¾ãããç®è¦ã§é»ç·ã®ä½ç½®ãåãã
ã¦ãã ããã
6 é
ã®æ¡ä»¶ãæºè¶³ããããã«é»ç·ãã»ãããã¦
ãã ããã
5-3.Wire setting
â Set in the barrel of the contact wire was coated
inorganic as shown.
Set between the wire barrel and the insulation
barrel the end face of insulation.
â» There is no stopper abuts the tip of the wire to the
hand tool. Match the position of the wires visually.
Set the wire so as to satisfy the conditions of
Section 6.
è¯ç·ãã¬ã«
Wire barrel
被è¦ãã¬ã«
Insulation barrel
é»ç·
Wire
5-4.å§ç
â é»ç·ã¨ã³ã³ã¿ã¯ããã»ããç¶æ
ã«ä¿æãããããª
ãããã«æ³¨æããªãããã³ãã«ãå¾ã
ã«æ¡ãç·
ãã¦ãã ããã
5-4.Crimping
â While holding the wire and contact position as set,
close the handles gradually with being careful not
to misaligned until the ratchet is released. In this
stage, crimping is completed.
5-5.ã³ã³ã¿ã¯ãã®åãåºã
â å§çå®äºå¾ãæ¡ãåãç·©ãæåã§ãã³ãã«ãåº
ãã¦ãã ããã
â¡ é»ç·ãã¤ãã¿ã軽ãå¼ãåºãã¾ãã
5-5.Contact removal
â After completing the crimping, spread the handle
manually loosen the grip force.
â¡ Pull the wire with a crimped contact easily to remove
it from the tool.
JAE Connector Div. Proprietary.
Copyright (C) 2013, Japan Aviation Electronics Industry, Ltd.
|
▷ |