MDM Datasheet, PDF (5/11 Pages) ITT Industries – Micro-D Metal Shell - .050 Contact Spacing

Micro-D Metal Shell - .050" Contact Spacing
Panel Cutouts
NOTE: See page 13 for rear panel mounting configuration.
Shell Sizes 9 thru 51
D
TYP.
C
B
FULL R.
(TYP.)
A
.015 (0.38)R.
MAX.(TYP)
C
D
A
TYP.
FULL R. (TYP.)
.100
(2.54)
+.005
-.000
+0.13
)
R TYP. -0.00
B
26˚/27˚TYP
Figure 1
Front Mounting
Figure 2
Rear Mounting
.450±.002
(11.43±0.05)
FULL R.
(TYP.)
MDM
C
.030 (0.76) TYP.
D
++
++
Figure 3
Edgeboard Mounting
PANEL REF.
Shell Size 100
.118
+.005
-.000
(3.00 +0.13 )
-0.00
1.805
+.005
-.000
(45.85
+0.13
-0.00
)
.361
+.004
-.000
(9.17 ⁺_-00..0100)
.015 (0.38)
R. MAX (TYP.)
1.456
+.004
-.000
(36.98 +0.10 )
-0.00 _{FULL R. (TYP.)}
Figure 1
Front Mounting
.118
+.005
-.000
(3.00
+0.13
-0.00
)
.125
(3.18 )
1.805
+.005
-.000
(45.85
+0.13
-0.00
)
.450+_.002
(11.43+_0.05)
.401
+.004
-.000
(10.18
+0.10
-0.00
)
1.520
+.004
-.000
(38.61
+0.10
-0.00
)
FULL R. (TYP.)
Figure 2
Rear Mounting
.030
(0.76) TYP.
1.805
+.005
-.000
(45.85
+0.13
-0.00
)
++
.118
+.005
-.000
(3.00
+0.13
-0.00
)
++
FULL R. (TYP.)
PANEL REF.
Figure 3
Edgeboard Mounting
For 9-51 Shell Sizes
NOTES:
1. Front panel mounting is the preferred mounting
method. Front panel mounting dimensions
(figure 1) will accommodate either #2-56 screws
or jackpost hardware.
2. Rear panel mount dimensions (figure 2) will
accommodate #2-56 screw hardware only.
When mounting the connector with rear panel
mount jackpost see the panel cut-out
dimensions.
3. Edgeboard mounting bracket (figure 3) uses #2-
56 screws. Dimension .450+/-.002 (11.43+/-
0.05) locates the MDM receptacle flush with the
end of the board.
For 100 Shell Size
NOTES:
1. Front mounting is the preferred mounting
method. Front panel mounting dimensions
(figure 1) will accommodate either #4-40 screws
or jackpost hardware.
2. Rear panel mount dimensions (figure 2) will
accommodate #4-40 screw hardware only see
the panel cut-out dimensions.
3.Edgeboard mounting bracket (figure 3) uses #4-
40 screws. Dimension .450+/-.002 (11.43+/-
0.05) locates the MDM receptacle flush with the
end of the board.
Shell
Size
9
15
21
25
31
37
51
Cutout
Figure
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
A
+.004
-.000
.408
.401
-
.558
.551
-
.708
.701
-
.808
.801
-
.958
.951
-
1.108
1.101
-
1.058
1.051
-
B
+.004
-.000
.271
.252
-
.271
.252
-
.271
.252
-
.271
.252
-
.271
.252
-
.271
.252
-
.315
.295
C
+.005
-.000
.570
.570
.570
.720
.720
.720
.870
.870
.870
.970
.970
.970
1.120
1.120
1.120
1.270
1.270
1.270
1.220
1.220
1.220
D
+.005
-.000
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
.089
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
www.ittcannon.com
11