ISL6741_14 Datasheet, PDF (7/28 Pages) Intersil Corporation – Flexible Double Ended Voltage and Current Mode PWM Controllers

ISL6740, ISL6741
Absolute Maximum Ratings (Note 6)
Supply Voltage, V_DD . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +20.0V
OUTA, OUTB, Signal Pins . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to V_REF
VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND - 0.3V to 6.0V
Peak GATE Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5A
ESD Classification
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . 1500V
Charged Device Model (Per EOS/ESD DS5.3, 4/14/93). . . . . . . . 1000V
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
16 Lead SOIC (Notes 4, 5) . . . . . . . . . . . . . .
74
33
16 Lead TSSOP (Notes 4, 5) . . . . . . . . . . . .
98
30
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . .-55°C to +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range
ISL6740Ix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C
ISL6741Ix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . . . . . 9VDC - 16VDC
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379.
5. For θ_JC, the “case temp” location is taken at the package top center.
6. All voltages are with respect to GND.
Electrical Specifications Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram” on
page 2 and page 3 and Typical Application Schematics on page 4 to page 6. 9V < V_DD < 20 V, R_TD = 51.1kΩ, R_TC = 10kΩ, C_T = 470pF, T_A = -40°C
to +105°C, Typical values are at T_A = +25°C. Boldface limits apply over the operating temperature range, -40°C to +105°C
PARAMETER
TEST CONDITIONS
MIN
(Note 7) TYP
MAX
(Note 7)
UNITS
SUPPLY VOLTAGE
Start-Up Current, I_DD
Operating Current, I_DD
UVLO START Threshold
V_DD < START Threshold
R_LOAD, C_OUTA,B = 0
C_OUTA,B = 1nF
-
95
140
µA
-
5.0
8.0
mA
-
7.0
12.0
mA
6.50 7.25
8.00
V
UVLO STOP Threshold
6.00 6.75
7.50
V
Hysteresis
0.25 0.50
0.75
V
REFERENCE VOLTAGE
Overall Accuracy
Long Term Stability
Fault Voltage
I_VREF = 0, -20mA
T_A = +125°C, 1000 hours
4.900 5.000
5.050
V
-
3
-
mV
4.10 4.55
4.75
V
V_REF Good Voltage
Hysteresis
4.25 4.75 V_REF - 0.05
V
75
165
250
mV
Operational Current (Source)
-20
-
-
mA
Operational Current (Sink)
5
-
-
mA
Current Limit
-25
-
-100
mA
CURRENT SENSE
Current Limit Threshold
CS to OUT Delay
V_ERROR = V_REF
0.55 0.6
0.65
V
-
35
50
ns
CS Sink Current
-
10
-
mA
Input Bias Current
-1.00
-
1.00
µA
CS to PWM Comparator Input Offset (ISL6741)
(Note 7)
-
80
-
mV
7
FN9111.6
December 2, 2011