ISL6161 Datasheet, PDF (6/11 Pages) Intersil Corporation – Dual Power Distribution Controller

ISL6161
.
TABLE 1. R_SENSE AND R_ILIM RECOMMENDATIONS
PCI-EXPRESS
ADD-IN CARD
CONNECTOR
R_ILIM
(kΩ)
3.3V R_SENSE 12V R_SENSE
(mΩ),
(mΩ),
NOMINAL NOMINAL
CR (A)
CR (A)
NOMINAL
CRVth
(mV)
X1
10
30, 3.3
150, 0.7
100
4.99
15, 3.5
90, 0.6
53
X4/X8
10
30, 3.3
40, 2.5
100
4.99
15, 3.5
20, 2.6
53
X16
10
30, 3.3
16, 6.3
100
4.99
15, 3.5
8, 6.6
53
NOTE: Nominal CR Vth = R_ILIM x 10µA.
TABLE 2.
C_TIM CAPACITOR
(µF)
NOMINAL TIME-OUT PERIOD
(ms)
0.022
4.4
0.047
9.4
0.1
20
NOTE: Nominal time-out period in seconds = C_TIM x 200kΩ.
The ISL6161 responds to a load short (defined as a current
level 3x the OC set point with a fast transition) by
immediately driving the relevant N-Channel MOSFET gate to
0V in ~3µs. The gate voltage is then slowly ramped up,
soft-starting the N-Channel MOSFET to the programmed
current regulation limit level. This is the start of the time-out
period if the abnormal load condition still exists. The
programmed current regulation level is held until either the
OC event passes or the time-out period expires. If the former
is the case, then the N-Channel MOSFET is fully enhanced
and the C_TIM charging current is diverted away from the
capacitor. If the time-out period expires prior to OC
resolution, then both gates are quickly pulled to 0V turning
off both N-Channel MOSFETs simultaneously.
Upon any UV condition, the PGOOD signal will pull low
when tied high through a resistor to the logic supply. This pin
is a fault indicator but not the OC latch-off indicator. For an
OC latch-off indication, monitor CTIM, pin 10. This pin will
rise rapidly to 12V once the time-out period expires. See
“Simplified Schematic” on page 2 for OC latch-off circuit
suggestion.
The ISL6161 is reset by a rising edge on the ENABLE pin
and is turned on by the ENABLE pin being driven low.
ISL6161 Application Considerations
In a non PCI-Express, motor drive application, Current loop
stabilization is facilitated through a small value resistor in
series with the gate timing capacitor. As the ISL6161 drives
a highly inductive current load, instability characterized by
the gate voltage repeatedly ramping up and down may
appear. A simple method to enhance stability is provided by
the substitution of a larger value gate resistor. Typically, this
situation can be avoided by eliminating long point-to-point
wiring to the load.
With the ENABLE internal pull-up, the ISL6161 is well suited
for implementation on either side of the connector where a
motherboard prebiased condition or a load board staggered
connection is present. In either case, the ISL6161 turns on in
a soft-start mode protecting the supply rail from sudden
current loading.
During the Time-Out delay period with the ISL6161 in
current limit mode, the V_GS of the external N-Channel
MOSFETs is reduced driving the N-Channel MOSFET switch
into a high r_DS(ON) state. Thus, avoid extended time-out
periods as the external N-Channel MOSFETs may be
damaged or destroyed due to excessive internal power
dissipation. Refer to the MOSFET manufacturers data sheet
for SOA information.
With the high levels of in-rush current e.g., highly capacitive
loads and motor start-up currents, choosing the current
regulation (CR) level is crucial to provide both protection
and still allow for this in-rush current without latching off.
Consider this in addition to the time-out delay when
choosing MOSFETs for your design.
Physical layout of R_SENSE resistors is critical to avoid
inadvertently lowering the CR and trip levels. Ideally, trace
routing between the R_SENSE resistors and the ISL6161
should be as direct and as short as possible with zero
current in the sense lines.
CORRECT
INCORRECT
TO ISEN AND
R_ISET
CURRENT
SENSE RESISTOR
FIGURE 1. SENSE RESISTOR PCB LAYOUT
6
FN9104.4
October 2, 2008