ISL6161 Datasheet, PDF (1/11 Pages) Intersil Corporation – Dual Power Distribution Controller

®
Data Sheet
October 2, 2008
ISL6161
FN9104.4
Dual Power Distribution Controller
The ISL6161 is a HOT SWAP dual supply power distribution
controller that can be used in PCI-Express applications.
Two external N-Channel MOSFETs are driven to distribute
and control power while providing load fault isolation. At
turn-on, the gate of each external N-Channel MOSFET is
charged with a 10µA current source. Capacitors on each
gate (see the “Typical Application Diagram” on page 1),
create a programmable ramp (soft turn-on) to control in-rush
currents. A built-in charge pump supplies the gate drive for
the 12V supply N-Channel MOSFET switch.
Overcurrent protection is facilitated by two external current
sense resistors and FETs. When the current through either
resistor exceeds the user programmed value, the controller
enters the current regulation mode. The time-out capacitor,
C_TIM, starts charging as the controller enters the time-out
period. Once C_TIM charges to a 2V threshold, both the
N-Channel MOSFETs are latched off. In the event of a hard
and fast fault of at least 3x the programmed current limit
level, the N-Channel MOSFET gates are pulled low
immediately before entering the time-out period. The
controller is reset by a rising edge on the ENABLE pin.
The ISL6161 constantly monitors both output voltages and
reports either one being low on the PGOOD output as a low.
The 12V PGOOD Vth is ~10.8V and the 3.3V Vth is ~2.8V
nominally.
Pinout
ISL6161
(14 LD SOIC)
TOP VIEW
12VS 1
12VG 2
V_DD 3
NC ₄
ENABLE 5
3VG 6
3VS 7
14 12VISEN
13 R_ILIM
12 GND
11 C_PUMP
10 C_TIM
9 PGOOD
8 3VISEN
Features
• HOT SWAP Dual Power Distribution and Control for
+12V and +3.3V
• Provides Fault Isolation
• Programmable Current Regulation Level
• Programmable Time-Out
• Charge Pump Allows the Use of N-Channel MOSFETs
• Power-Good and Overcurrent Latch Indicators
• Adjustable Turn-On Ramp
• Protection During Turn-On
• Two Levels of Current Limit Detection Provide Fast
Response to Varying Fault Conditions
• 1µs Response Time to Dead Short
• 3µs Response Time to 200% Current Overshoot
• Pb-Free Available (RoHS compliant)
Applications
• PCI-Express Applications
• Power Distribution and Control
• Hot Plug, Hot Swap Components
Ordering Information
PART
NUMBER
PART
MARKING
TEMP.
RANGE
(°C)
PKG.
PACKAGE DWG. #
ISL6161IBZA* ISL6161 IBZ
(Note)
-40 to +85 14 Ld SOIC M14.15
(Pb-free)
ISL6161CB* ISL6161CB
0 to +70 14 Ld SOIC M14.15
ISL6161CBZA* 6161CBZ
(Note)
0 to +70 14 Ld SOIC M14.15
(Pb-free)
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel
specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special
Pb-free material sets, molding compounds/die attach materials, and
100% matte tin plate plus anneal (e3 termination finish, which is RoHS
compliant and compatible with both SnPb and Pb-free soldering
operations). Intersil Pb-free products are MSL classified at Pb-free peak
reflow temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020
Typical Application Diagram
OPTIONAL
V_DD^RFILTER
C_FILTER
12V
C_GATE
ENABLE
INPUT
3.3V
C_GATE
C_PUMP
R_SENSE
ISL6161
12VS 12VISEN
12VG ^RILIM
V_DD
GND
C_PUMP
ENABLE ^CTIM
3VG PGOOD
3VS 3ISEN
R_SENSE
R_LOAD
R_ILIM
C_TIM
3.3V
R_LOAD
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003, 2004, 2008. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.