ISL6123_11 Datasheet, PDF (6/23 Pages) Intersil Corporation – Power Sequencing Controllers

ISL6123, ISL6124, ISL6125, ISL6126, ISL6127, ISL6128, ISL6130
Absolute Maximum Ratings (Note 6)
V_DD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6.0V
GATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V_DD+6V
ISL6125 LOGIC OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V_DD + 0.3V
UVLO, ENABLE, ENABLE, SYSRST . . . . . . . . . . . . . . . . . . -0.3V to V_DD + 0.3V
RESET, DLY_ON, DLYOFF . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V_DD + 0.3V
Operating Conditions
V_DD Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . .+1.5V to +5.5V
Temperature Range (T_A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Thermal Information
Thermal Resistance (Typical)
θ_JA (°C/W) θ_JC (°C/W)
24 Ld 4x4 QFN Package (Notes 4, 5) . . . . .
46
8
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+125°C
Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379 for details.
5. For θ_JC, the “case temp” location is the center of the exposed metal pad on the package underside.
6. All voltages are relative to GND, unless otherwise specified.
Electrical Specifications V_DD = 1.5V to +5V, T_A = T_J = -40°C to +85°C, unless otherwise specified. Boldface limits apply over the
operating temperature range, -40°C to +85°C.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
(Note 7)
MAX
TYP
(Note 7) UNIT
UVLO
Falling Undervoltage Lockout Threshold
Undervoltage Lockout Threshold Tempco
Undervoltage Lockout Hysteresis
Undervoltage Lockout Threshold Range
Undervoltage Lockout Delay
V_UVLOvth
TC_UVLOvth
V_UVLOhys
RUVLOvth
TUVLOdel
T_J = +25°C
Max V_UVLOvth- Min V_UVLOvth
ENABLE satisfied
619
633
647
mV
40
µV/°C
10
mV
7
mV
10
ms
Transient Filter Duration
DELAY ON/OFF
t_FIL
V_DD, UVLO, ENABLE glitch filter
30
µs
Delay Charging Current
Delay Charging Current Range
DLY_ichg
DLY_ichg_r
V_DLY = 0V
DLY_ichg(max) - DLY_ichg(min)
0.92
1
0.08
1.08
µA
µA
Delay Charging Current Temperature
Coefficient
TC_DLY_ichg
0.2
nA/°C
Delay Threshold Voltage
DLY_Vth
1.238
1.266
1.294
V
Delay Threshold Voltage Temperature
Coefficient
TC_DLY_Vth
0.2
mV/°C
ENABLE/ENABLE, RESET AND SYSRST I/O
ENABLE Threshold
ENABLE Threshold
ENABLE/ENABLE Hysteresis
ENABLE/ENABLE Lockout Delay
ENABLE/ENABLE Input Capacitance
V_ENh
V_ENh
V_{ENh -}V_ENl
t_{delEN_LO}
Cin_en
Measured at V_DD = 1.5V
UVLO satisfied
1.2
V
0.5 V_DD
V
0.2
V
10
ms
5
pF
RESET Pull-up Voltage
RESET Pull-Down Current
Vpu_rst
I_RSTpd1
I_RSTpd3
I_RSTpd5
V_DD = 1.5V, RST = 0.1V
V_DD = 3.3V, RST = 0.1V
V_DD = 5V, RST = 0.1V
V_DD
V
5
mA
13
mA
17
mA
6
FN9005.11
August 25, 2011