ISL54056 Datasheet, PDF (5/12 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.65V to +4.5V, Single Supply, Quad SPDT (Dual DPDT) Analog Switch

ISL54056
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V_INH = 1.4V, V_INL = 0.5V (Note 4),
unless otherwise specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
Charge Injection, Q
OFF Isolation
C_L = 1.0nF, V_G = 0V, R_G = 0Ω (See Figure 2)
25
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS
25
(See Figure 4)
126
pC
65
dB
Crosstalk (Channel-to-Channel)
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS
25
(See Figure 6)
-85
dB
Total Harmonic Distortion
f = 20Hz to 20kHz, V_COM = 2V_P-P, R_L = 600Ω
25
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 7)
25
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 7)
25
POWER SUPPLY CHARACTERISTICS
0.012
%
38
pF
102
pF
Positive Supply Current, I+
V+ = 3.6V, V_IN = 0V or V+
25
0.021
μA
Full
0.72
μA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_INL
Input Voltage High, V_INH
Input Current, I_INH, I_INL
V+ = 3.6V, V_IN = 0V or V+
Full
Full
1.4
Full
-0.5
0.5
V
V
0.5
μA
Electrical Specifications - 1.8V Supply
Test Conditions: V+ = +1.65V to +2V, GND = 0V, V_INH = 1.0V, V_INL = 0.4V (Note 4),
unless otherwise specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
Full
0
V+
V
ON Resistance, R_ON
V+ = 1.8V, I_COM = 100mA, V_NO or V_NC = 0V to V+
25
(See Figure 5)
Full
0.65
0.8
Ω
0.85
Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 1.65V, V_NO or V_NC = 1.0V, R_L = 50Ω, C_L = 35pF 25
50
ns
(See Figure 1)
Full
55
ns
Turn-OFF Time, t_OFF
V+ = 1.65V, V_NO or V_NC = 1.0V, R_L = 50Ω, C_L = 35pF 25
25
ns
(See Figure 1)
Full
30
ns
Break-Before-Make Time Delay, t_D V+ = 2.0V, V_NO or V_NC = 1.0V, R_L = 50Ω, C_L = 35pF Full
8
ns
(See Figure 3)
Charge Injection, Q
C_L = 1.0nF, V_G = 0V, R_G = 0Ω (See Figure 2)
25
DIGITAL INPUT CHARACTERISTICS
48
pC
Input Voltage Low, V_INL
Input Voltage High, V_INH
Input Current, I_INH, I_INL
V+ = 2.0V, V_IN = 0V or V+
Full
Full
1.0
Full
-0.5
0.4
V
V
0.5
μA
5
FN6357.1
October 30, 2006