ISL54056 Datasheet, PDF (3/12 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.65V to +4.5V, Single Supply, Quad SPDT (Dual DPDT) Analog Switch

ISL54056
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±500mA
ESD Rating:
HBM COM_X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>9kV
HBM NO_X, NC_X, IN_X, V+, GND . . . . . . . . . . . . . . . . . . . . . . .>6kV
MM COM_X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>700V
MM NO_X, NC_X, IN_X, V+, GND . . . . . . . . . . . . . . . . . . . . . . .>300V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1kV
Thermal Information
Thermal Resistance (Typical, Note 3)
θ_JA (°C/W)
μTQFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL54056IRUZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, V_INH = 1.6V, V_INL = 0.5V (Note 4),
unless otherwise specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
Full
0
V+
V
ON Resistance, R_ON
V+ = 3.9V, I_COM = 100mA, V_NO or V_NC = 0V to V+
25
0.4
Ω
(See Figure 5)
Full
0.45
Ω
R_ON Matching Between Channels, V+ = 3.9V, I_COM = 100mA, V_NO or V_NC = Voltage at
25
0.05
Ω
ΔR_ON
max R_ON (Note 7)
Full
0.06
Ω
R_ON Flatness, R_FLAT(ON)
V+ = 3.9V, I_COM = 100mA, V_NO or V_NC = 0V to V+
25
0.05
Ω
(Note 6)
Full
0.05
Ω
NO or NC OFF Leakage Current, V+ = 4.5V, V_COM = 0.3V, 3V, V_NO or V_NC = 3V, 0.3V
25
-70
I_NO(OFF) or I_NC(OFF)
Full
-165
70
nA
165
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 4.5V, V_COM = 0.3V, 3V, or V_NO or V_NC = 0.3V, 3V 25
Full
-70
-165
70
nA
165
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 3.9V, V_NO or V_NC = 3.0V, R_L = 50Ω, C_L = 35pF
25
33
ns
(See Figure 1)
Full
38
ns
Turn-OFF Time, t_OFF
V+ = 3.9V, V_NO or V_NC = 3.0V, R_L = 50Ω, C_L = 35pF
25
16
ns
(See Figure 1)
Full
21
ns
Break-Before-Make Time Delay, t_D V+ = 4.5V, V_NO or V_NC = 3.0V, R_L = 50Ω, C_L = 35pF Full
3
ns
(See Figure 3)
Charge Injection, Q
OFF Isolation
C_L = 1.0nF, V_G = 0V, R_G = 0Ω (See Figure 2)
25
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS
25
(See Figure 4)
248
pC
65
dB
Crosstalk (Channel-to-Channel)
R_L = 50Ω, C_L = 5pF, f = 100kHz, V_COM = 1V_RMS
25
(See Figure 6)
-85
dB
Total Harmonic Distortion
f = 20Hz to 20kHz, V_COM = 2V_P-P, R_L = 600Ω
25
0.008
%
3
FN6357.1
October 30, 2006